【摘 要】
：
A high power and good beam quality InGaAs/GaAs quantum well semiconductor disk laser at 1 015 nm wavelength is reported. The semiconductor wafer is grown in reverse order: substrate is on the window side and the distributed Bragg reflector is the last gro
【出 处】
：
ChineseOpticsLetters
论文部分内容阅读
A high power and good beam quality InGaAs/GaAs quantum well semiconductor disk laser at 1 015 nm wavelength is reported. The semiconductor wafer is grown in reverse order: substrate is on the window side and the distributed Bragg reflector is the last grown epilayer. Then the wafer is up-side-down and capillary bonded to a SiC heatsink, and the substrate is chemically etched. Because the total thickness of the substrate-removed structure is less than 10 μm, the thermal management of the laser is significantly improved, and the maximum output power over 0.6 W is obtained using a 3% output coupler and 3.2 W incident pump power. The M2 factors of 1.02 and 1.01 indicate a near-diffraction-limited beam quality. To further reveal the characteristics of this substrate-etched structure on the thermal management, the heat flux and the temperature distribution of the gain wafer are numerically analyzed, and the corresponding results are discussed.
其他文献
在化学破坏下能态过程中建立粒子数反转的思想方面，文献[1]提出了在不稳定分子，如氢化汞分子的基态中的束缚-束缚跃迁上获得激光振荡的设想。图1示出HgH(A2Π1/2-X2Σ1/2跃迁的激光器工作图。由于必须考虑大量的过程和缺乏稠密气体中HgH分子动力学方面的信息，这种激光器的定量分析工作是困难的。在研究气体放电Hg-H2等离子体的辐射光谱行为与它的密度和组分的关系时，可能获得所要求数据的重要部分。本文报导这些研究结果。
We briefly outline a modelling strategy, combining quantum chemistry and molecular dynamics simulations, for obtaining macroscopic nonlinear optical coeffcients in guest-host systems like chromophores in solutions or in polymer matrices. The parameters re
报道了给体-受体电子转移型材料zinc-tetraphenylbenzoporphrin zinc-tetrapheyl benzotribenzoporphrin\phydroxybenzaldhyde\poly (methyl) methacrylate 的光子选通多重烧孔过程。 结果表明要获得高质量的多重光谱孔，从短波往长波的逐次烧孔更为有效。其影响来自与波长有关的光致填孔现象。造成该填孔的主要机制是赝声子边带的作用。理论拟合与实验结果相符。
A spectroscopic method to determine thickness of quartz wave plate is presented. The method is based on chromatic polarization interferometry. With the polarization-resolved transmission spectrum (PRTS) curve, the phase retardation of quartz wave plate ca
The mechanical properties of fluorescent microtubules (MTs) are probed with dual-optical tweezers system. The results indicate that the fluorescent MTs are much easier to be extended compared with those without fluorescence. Such MT can be extended by 30%
将激光诱导击穿光谱技术(LIBS)应用于测量飞灰中C、Si、Al、Mg和Fe等主要元素，飞灰样品与粘结剂KBr混合压制成压片，对比分析不同环境气体（CO2，空气，N2，Ar）下飞灰等离子体特性，探究环境气体对飞灰测量的影响。研究结果表明Ar环境下光谱强度最高，N2次之，空气环境下强度稍低于N2环境，而CO2环境下不仅整体光谱强度最低，且由于背景气体CO2中存在的C元素被激发,对飞灰含碳量的测量存在严重的干扰。同时对比不同环境条件下的等离子体温度特性，结果表明Ar条件下等离子体温度最高，CO2条件下等离子体
详细研究了不同温度下着色KCl晶体R2心和756.6 nm零声子线以及着色KBr晶体R2心零声子线的产生.利用恰当的热处理，可产生和增强零声子线，并给出了相应的物理解释.
对GdFeCo/AlN/DyFeCo静磁耦合多层薄膜变温磁化方向变化进行了研究。结果表明读出层GdFeCo随温度上升从平面磁化转变成垂直磁化,转变过程中受饱和磁化强度(Ms)和有效各向异性常数影响,但主要受饱和磁化强度(Ms)的影响。在高温时读出层的磁化强度很小,退磁场能减小,在静磁耦合作用下,使GdFeCo读出层的磁化方向发生转变,而且磁化方向的转变在较小的温度范围内变化较快。
研究了K452高温合金激光增材修复时的开裂特性及液化裂纹产生机理,采用低热输入脉冲激光工艺控制液化裂纹的产生,研究了修复区域的显微组织和力学性能。结果表明,K452高温合金在激光增材修复过程中容易产生液化裂纹,裂纹通常起源于热影响区且沿晶界向基体和修复区域扩展;拉应力作用下热影响区晶界上的液膜形成了液化裂纹。低热输入脉冲激光工艺可以有效控制液化裂纹的产生,脉冲激光修复试样修复区的平均硬度为267.9 HV;抗拉强度和屈服强度分别为814.3 MPa和685.8 MPa,略大于铸态基体的强度;延伸率为4.8