COMPLETE PARAMETER MEASUREMENT FOR MIMO BISTATIC RADAR WITHOUT SYNCHRONIZATION

来源 :Journal of Electronics(China) | 被引量 : 0次 | 上传用户:dqhzzy
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
In order to measure the range, angle, and Doppler frequency of the target without any synchronization in the bistatic radar, a novel complete parameter estimation method based on separability of a pair of Linear Frequency Modulation (LFM) signal is presented. The Doppler fre-quency is measured by the time difference between two peak positions corresponding to the positive and the negative LFM return signal respectively. Direction Of Departures (DODs) and Direction Of Arrivals (DOAs) of the target are estimated by constructing a special eigenmatrix in which the es-timated angles can be extracted from the eigenvalue or the eigenvector. The target position can be located in the presence of the estimated DODs, DOAs and the signal delay difference between the echo and the directive wave signal in Multiple Input Multiple Output (MIMO) bistatic radar without any synchronization. The correctness and effectiveness of the proposed method are verified by the computer simulation. In order to measure the range, angle, and Doppler frequency of the target without any synchronization in the bistatic radar, a novel complete parameter estimation method based on separability of a pair of Linear Frequency Modulation (LFM) signal is presented. The Doppler fre- quency is measured by the time difference between two peak positions corresponding to the positive and the negative LFM return signal respectively. The target position can be located in the presence of the estimated DODs, DOAs and the signal delay difference between the echo and the directive wave signal in Multiple Input Multiple Output (MIMO) bistatic radar without any synchronization. The correctness and effectiveness of the proposed method are verified by the computer simulation.
其他文献
结合客车总装下线后存在的5个修补漆问题典型案例,阐述了问题现状及产生原因,并制定了相关改善方案,较好地改善了问题,进一步提高了车辆的漆面外观质量.
接触网零部件是电气化铁道供电系统中的重要部件.基于我国现有接触网零部件的腐蚀状况,分析了其发生腐蚀的原因,提出了接触网金属零部件的防护措施.并基于试验结果,已经在高
采用大分子双酚A型环氧树脂为主体树脂,HDI三聚体为固化剂,添加颜填料和助剂,制备了酸处理车间墙面用环氧聚氨酯涂料,研究了环氧树脂当量、NCO/OH值、催化剂、阻聚剂、膨润土
通过三维激光扫描仪采集华晨汽车现有涂装车间点云数据,并导入PDPS软件中,建立与涂装车间生产线实际结构、尺寸和位置相一致的数字孪生工厂,以前处理-电泳槽、烘干炉和强冷室
采用EDS能谱元素分析、SEM扫描电镜等分析方法,对车身金属件局部电泳不良附着力差的原因进行分析,试验表明:产生缺陷的钢板表面含铬、氯钝化层,影响了磷化反应进行,没有形成
介绍了UV固化聚丙烯酸树脂的合成方法,讨论了十二烷基硫醇和甲基苯乙烯线性二聚体这两种链转移剂对合成树脂的黏度、外观、分子量、分子量分布以及漆膜性能的影响,结果表明甲
通过研究消光剂的基础性能以及影响消光效果的不同因素,探讨了消光剂含量、消光剂种类以及消光剂吸油量对漆膜光泽的影响.结果 表明:消光剂含量与漆膜光泽呈反比关系,消光效
为解决铝合金轮毂在生产或运输过程中产生的压痕问题,对抗压痕透明漆NP-17在铝合金车轮上的应用进行了可行性研究,选取抗压痕透明漆NP-17和普通透明漆RF20-0010/1作对比,对喷
随着模块化UPS在市场上的普及率越来越高,客户对于这种更符合客户应用的UPS系统的关注度也越来越加强,但是,相对于传统的UPS系统,客户对模块化UPS还存在着种种疑虑,主要集中
阐述了亚光漆的消光原理以及施工因素对其光泽度稳定性的影响,在漆膜烘干方式(自干或烘干)、干燥时的空气相对湿度、施工后漆膜放置时间3个因素中,干燥时的空气相对湿度对漆