Nitrogen Doped Multi-channel Graphite for High Rate and High Capacity Li Ion Battery

来源 :武汉理工大学学报(材料科学版)(英文版) | 被引量 : 0次 | 上传用户:wenping1980
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Nitrogen doped multi-channel graphite was successfully prepared by using nitrogen doping and KOH etching technologies. The three-electrode and EIS tests indicates that the etched graphite possesses lower electrochemical resistance than the pristine graphite. The coin cell tests demonstrate that N doped multi-channel graphite possesses a specific capacity of 361 mAh/g and coulombic efficiencies of 91.4%. No dramatic irreversible capacity loss results from the increased specific surface area (from 1.60 to 2.08 m2/g), removing the need for a trade-off between irreversible capacity loss and surface area. Full polymer cells were fabricated and electrochemical capabilities were measured. In 3C fast charge protocol, the charging capacity can reach 51% within 10 min charge, and 100% within 30 min, demonstrating excellent fast charging characteristic. The fast charge cycle performance with 3C-rate charge and 1C-rate discharge from 4.35-3.0 V was conducted at RT temperature. The capacity retention is 94% after 600 cycles, which shows good cycle performance.
其他文献
Silicon carbide ceramics with different thicknesses/diameter ratios were prepared by using ultra-fine silicon carbide powder with the sintering additives of 1.0 wt% boron and 1.5 wt% carbon. The influence of thickness/diameter ratio on the microstructure
The titanium carbide phase was synthesized in laser melted-pool in situ as the reinforced particles of nickel based composite coating on Ti-6Al-4V alloy surface using the nickel and graphite blending powder by laser cladding. The microstructure investigat
Ag-modified TiO2 nanoflowers were prepared using a two-step process. The experimental process is green and free from contamination and can be synthesized directly at room temperature. Compared with pure TiO2, Ag-modified TiO2 enhances the absorption of vi
We introduced a parameter rs (the radius of the pores where the meniscus forms), which is composed of two factors, i e, water loss and cumulative pore size distribution (PSD), to provide a better explanation of the influence of superplasticizers(SPs) on e
Si/Cu3Si@C composites encapsulated in CNTs network (SCC-CNTs) were synthesized via the combination of ball-milling and CVD methods. SCC-CNTs consist of conductive Cu3Si, amorphous carbon layer, cross-linked CNTs, and the etched pores, which can play the s
A simple route to synthesize the polyaniline (PANI) nanofibers with diameter about 150 nm was reported.In this strategy,the PANI nanofibers were fabricated by electrochemical deposition by using two-electrode configuration in 0.01 M aniline and 0.01 M H2S
A series of solar radiation tests for the polytetrafluoroethylene(PTFE) bulk and film samples were carried out using Q-SUN XE-3-HSC type Solar Radiation Simulator,with the test parameters as follows:radiation intensity is 1 120 W/m2,temperature is 55 ℃ an
A series of poly (ethylene oxide) (PEO) membranes with star-like structures for CO2/H2 separation were prepared by the photo-polymerization method.The structure of PEO membrane was characterized by Fourier transform infrared spectroscopy (FTIR).The therma
Nanocrystalline and amorphous LaMg12-type LaMg11Ni+xwt% Ni (x = 100, 200) alloys were synthesized by mechanical milling. Effects of Ni content and milling time on the gaseous and electrochemical hydrogen storage kinetics of as-milled alloys were investiga