Porous core-shell CoMn2O4 microspheres as anode of lithium ion battery with excellent performances a

来源 :能源化学 | 被引量 : 0次 | 上传用户:ixiay
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Porous core-shell CoMn2O4 microspheres of ca.3-5 μm in diameter were synthesized and served as anode of lithium ion battery.Results demonstrate that the as-synthesized CoMn2O4 materials exhibit excellent electrochemical properties.The CoMn2O4 anode can deliver a large capacity of 1070 mAh g-1 in the first discharge,a reversible capacity of 500 mAh g-1 after 100 cycles with a coulombic efficiency of 98.5% at a charge-discharge current density of 200mA g-1,and a specific capacity of 385 mAh g-1 at a much higher charge-discharge current density of 1600mA g-1.Synchrotron X-ray absorption fine structure (XAFS) techniques were applied to investigate the conversion reaction mechanism of the CoMn2O4 anode.The X-ray absorption near edge structure (XANES) spectra revealed that,in the first discharge-charge cycle,Co and Mn in CoMn2O4 were reduced to metallic Co and Mn when the electrode was discharged to 0.01 V,while they were oxidized respectively to CoO and MnO when the electrode was charged to 3.0V.Experiments of both XANES and extended X-ray absorption fine structure (EXAFS) revealed that neither valence evolution nor phase transition of the porous core-shell CoMn2O4 microspheres could happen in the discharge plateau from 0.8 to 0.6V,which demonstrates the formation of solid electrolyte interface (SEI) on the anode.
其他文献
A series of titania nanoparticles and nanotubes deposited with various quantities of bismuth (Bi) were prepared via sol-gel and hydrothermal methods,respectively.They were then characterized using X-ray diffraction spectroscopy (XRD),X-ray photo electron
A flexible electrode of nickel diselenide/carbon fiber cloth (NiSe2/CFC) is fabricated at room temperature by a simple and efficient electrodeposition method.Owing to NiSe2 character of nanostructure and high conductivity,the as-synthesized electrodes pos
In this work,CaO-NiO mixed oxide powders were evaluated as consecutive CO2 chemisorbents and catalytic materials for hydrogen production thought the CH4 reforming process.Between the NiO-impregnated CaO and CaO-NiO mechanical composite,the first one prese
The increase in natural gas reserves makes methane a significant hydrocarbon feedstock.However,the direct catalytic conversion of methane into liquid fuels and useful chemicals remains a great challenge,and many studies have been devoted to this field in
Direct methanol fuel cells (DMFCs) are very promising power source for stationary and portable miniature electric appliances due to its high efficiency and low emissions of pollutants.As the key material,catalysts for both cathode and anode face several p
Sodium-ion batteries (SIBs) have attracted increasing attention in the past decades,because of high overall abundance of precursors,their even geographical distribution,and low cost.Na3V2(PO4)3 (NVP),a typical sodium super ion conductor (NASICON)-based el
Numerous fabrication methods have been developed for high-efficiency perovskite solar cells (PSCs).However,these are limited to spin-coating processes in a glove box and are yet to be commercialized.Therefore,there is a need to develop a controllable and
Organic carbonyl compounds are considered as promising candidates for lithium batteries due to their high capacity and environmental friendliness.However,they suffer from serious dissolution in the electrolyte,leading to fast capacity decay.Here we report
To design the high-energy-density Li-ion batteries,the anode materials with high specific capacity have attracted much attention.In this work,we adopt the first principles calculations to investigate the possibility of a new two dimensional boron material
LiNi0.8Co0.15Al0.05O2 (NCA) material is successfully synthesized with a modified co-precipitation method,in which NH3.H2O and EDTA are used as two chelating agents.The obtained LiNi0,8Co0J5Al0.05O2 material has well-defined layered structure and uniform e