固溶温度对022Cr22Ni5M03N双相不锈钢组织和性能的影响

来源 :特殊钢 | 被引量 : 0次 | 上传用户：cyqlsc

【摘要】

：

试验研究了1000℃4h和1060℃4h固溶处理后022Cr22Ni5Mo3N钢Φ75 mm材的组织和力学性能.结果表明,022Cr22Ni5Mo3N钢Φ75 mm材终锻温度970℃空冷的组织(体积分数)约为铁素体31％,奥氏体56％,析出物13％;1000℃4h固溶后为铁素体38％,奥氏体60％,析出物2％;1060℃4h固溶后铁素体50％,奥氏体50％,该钢通过采用1060℃固溶后,拉伸断裂强度731 MPa,延伸率38％,冲击功AKV(-40℃)76 ～81 J,满足标准要求.

【作者】

：

李宁

【机构】

：

沈阳科金特种材料有限公司,沈阳110101

【出处】

：

特殊钢

【发表日期】

：

2021年5期

【关键词】

：

022Cr22Ni5Mo3N钢固溶温度组织铁素体冲击韧性

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

其他文献

Efficient CO2 to CO conversion at moderate temperatures enabled by the cobalt and copper co-doped fe

Chemical looping technology holds great potential on efficient CO2 splitting with much higher CO pro-duction and CO2 splitting rate than photocatalytic processes. Conventional oxygen carrier requires high temperature (typically 850–1000 ℃) to ensure suffi

期刊

Chemical loopingOxygen carrierCO2 splittingFerrite

N08800铁镍基合金热变形行为及组织演变

在Gleeble-3800热模拟机上采用等温压缩实验研究了N08800铁镍基合金(/％:0.015C,20.8Cr,31.2Ni,0.42Al,0.35Ti)的高温压缩变形行为.获得合金在温度为1150～1280℃、应变速率为1～20 s-1条件下的真应力-真应变曲线.通过线性回归得到N08800合金的高温材料常数a为0.0092,n为4.34,热变形激活能Q为432780J/mol,建立了N08800合金的热变形峰值本构模型.结果表明,N08800合金在热压缩变形过程中,高温低应变速率下,动态再结晶容

期刊

N08800铁镍基合金热变形行为本构模型1 200~1 250℃动态再结晶

Simple synthesis of sandwich-like SnSe2/rGO as high initial coulombic efficiency and high stability

Metal selenides owing to their high theoretical capacity and good conductivity are considered as one of the potential candidates for the anode materials of sodium-ion batteries (SIBs). However, their practical applications are greatly restricted by the po

期刊

Sodium-ion batteriesInitial coulombic efficiencyEx-situ XRDSEITin diselenide

Quantitative behavior of vibrational excitation in AC plasma assisted dry reforming of methane

Quantitative behavior of non-equilibrium excitation by direct electron impact in low-temperature dry reforming of methane was investigated by integrated studies of experimental validation and kinetic mod-eling. A plasma chemistry kinetic mechanism incorpo

期刊

Non-equilibrium plasmaDry reformingVibrational excitationLow-temperature chem

Electrostatic self-assembly of MXene and edge-rich CoAl layered double hydroxide on molecular-scale

It is highly desirable to design and synthesize two-dimensional nanostructured electrode materials with high electrical conductivity, large electrolyte-accessible surface area and more exposed active sites for energy storage applications. Herein, MXene/Co

期刊

MXeneHetero-assemblySupercapacitorVolumetric performanceHeterostructure

Additives in metal halide perovskite films and their applications in solar cells

The booming growth of organic-inorganic hybrid lead halide perovskite solar cells have made this promis-ing photovoltaic technology to leap towards commercialization. One of the most important issues for the evolution from research to practical applicatio

期刊

Perovskite solar cellAdditiveSolar modulesFilm quality

Performance improvement of lithium-ion battery by pulse current

Periodically changed current is called pulse current. It has been found that using the pulse current to charge/discharge lithium-ion batteries can improve the safety and cycle stability of the battery. In this short review, the mechanisms of pulse current

期刊

Lithium ion batteryPulse currentActivationWarming upFast chargingLithium de

10B28含硼冷镦钢结疤形成分析及控制实践

分析得出10B28钢结疤的主要原因是钢水N含量偏高,钢水中的Ti不足以完全固N,致使大量的细小的BN在晶界析出,铸坯在矫直过程形成裂纹,进而在轧制过程形成线材表面结疤.取样分析证实,精炼过程使用高N含量(4.6％)缓释脱氧剂造渣是钢水含N高的主要原因;使用铝粒替代缓释脱氧剂脱氧造渣,精炼过程增N量可由43.4×10-6降至11.4×10-6.通过将转炉出钢C由0.06％提高至≥0.08％、降低精炼前期加热功率、铝粒替代缓释脱氧剂造渣等措施,10B28钢N含量稳定控制在70×10-6以下,线材合格率由不足5

期刊

冷镦钢10B28线材结疤N含量缓释脱氧剂

Rolling up MXene sheets into scrolls to promote their anode performance in lithium-ion batteries

Although Ti3C2 MXene sheets have attracted extensive attention in lithium-ion storage techniques, their restacking makes against and even hinders the Li ions diffusion within them, thereby decreasing the capacity as well as rate performance of conventiona

期刊

Ti3C2Tx scrollsSi nanoparticlesLithium-ion batteriesAnode

软丁腈代替硬丁腈胶粘剂的性能对比研究

通过设计符合硬丁腈性能标准的软丁腈胶料配方,对比了可塑度、硫化特性以及粘合性能.结果表明,替代后的软丁腈橡胶各项性能均能满足硬丁腈性能的指标要求,且软丁腈与硬丁腈相比具有更好的加工性能.

期刊

硬丁腈橡胶软丁腈橡胶胶粘剂

固溶温度对022Cr22Ni5M03N双相不锈钢组织和性能的影响

与本文相关的学术论文