【摘 要】
:
Myocardial infarction (MI) is one of the common cardiovascular diseases that occurs with a blockage in one or more of the coronary arteries to lead to the damage of the myocardium,resulting in a life-threatening condition.To repair the damaged myocardium
【机 构】
:
Department of Cardiovascular Surgery of the First Affiliated Hospital & Institute for Cardiovascular
论文部分内容阅读
Myocardial infarction (MI) is one of the common cardiovascular diseases that occurs with a blockage in one or more of the coronary arteries to lead to the damage of the myocardium,resulting in a life-threatening condition.To repair the damaged myocardium in MI,researchers are looking forwards to new ways to postpone the progression of myocardial injury.Cardiac patches,the scaffolds layered on the heart surface,can provide mechanical support for the infarction site and improve cardiac function by delivering various bioactive factors or cells,showing considerable curative effect in the treatment of MI.Biomate-rials with certain biocompatibility and mechanical properties have received widespread attention for the application in cardiac patches.In this review,we focus on the recent progress on these biomaterials-based cardiac patches,which could be categorized into two types according to the sources of materials including (i) natural materials and (ii) synthetic materials.The major advantages and current challenges of each type are discussed and a brief perspective on the future research directions is presented.
其他文献
研究了热处理对爆炸焊接T2+Q345R复合板组织和性能的影响.结果表明,热处理温度对T2+Q345R复合板的剪切、拉脱、伸长率等影响不明显,650℃以下,复层晶粒度增长缓慢,界面处异种金相组织厚度较爆炸态变化不大;650℃以上,随温度升高,复层晶粒度急剧增长,界面处异种金相组织厚度较爆炸态快速增加.
对铝-钢爆炸复合过渡接头的材质及规格、制造工艺、标准规范、性能要求、焊接要求等方面进行了介绍及分析,为过渡接头的检验、验收和标准的修订提供了一定的参考.
尼龙锁紧套是地铁用双层非线性减振扣件的零件之一,其将上下铁垫板及中间减振垫锁定成为一体,实现扣件预组装,进而大大减少现场施工工作量.根据技术要求,尼龙锁紧套完成加工后,应进行冲击韧性试验,要求能承受50 kg锤头从45 mm高度自由落体冲击6次而不损坏.根据尼龙锁紧套技术条件,设计了冲击试验工装,借助有限元软件对结构进行了冲击计算.根据计算结果对结构进行了进一步优化,最终得到满足冲击试验强度的优化后结构,并且重量从原来的15.87 kg减少至8.17 kg,方便该冲击试验的反复拆装操作.根据优化后图纸加工
采用IPG光纤激光器对8 mm厚的TA5钛合金进行激光自熔焊接,并对焊接接头的微观组织和力学性能进行分析.结果表明,激光焊接接头表面成形连续、均匀、无飞溅,内部无气孔和裂纹等缺陷.母材组织为细小均匀的等轴α相;焊缝区组织主要由粗大的β柱状晶粒、大量的针状马氏体α\'以及少量的板条马氏体组成;热影响区组织主要由等轴α相、少量的针状马氏体α\'和少量的残余β组成;在熔合线的边界,柱状晶粒与等轴晶粒联生结晶、外延生长,保证了焊接接头的稳定连接.焊接接头各区域的显微硬度差异较大,最高硬度出现在熔合线附近,
通过溶胶-凝胶法以钛酸四丁酯为前驱体,醋酸为催化剂制备TiO2溶胶,利用γ-甲基丙烯酰氧基丙基三甲氧基硅烷(KH570)对其进行低表面能修饰,得到疏水改性的TiO2溶胶,然后喷涂到滤料表面使其具有超疏水性.对改性前后滤料的润湿性、表面形貌、化学成分和过滤性能进行分析.结果表明:改性涂层均匀沉积在滤料表面,将纤维表面完整包裹,改性后滤料的水接触角达156.29°.在过滤风速为0.043~0.127 m/s时对粒径为0.3μm的颗粒进行过滤性能测试,改性后滤料的过滤效率比未改性滤料平均增加2.7672%,过滤
CaCO3/CaO热化学储热体系在清洁能源发电领域具有广阔的应用前景,有助于尽早实现碳达峰、碳中和.本文通过物理混合法制备了掺杂TiO2的CaCO3/CaO复合储热材料,系统研究了TiO2掺杂对CaCO3/CaO循环稳定性和储/放热过程中反应性能的影响.实验结果表明:在掺杂摩尔比为100:2.5(Ca:Ti)时,复合材料展现出了最佳的循环稳定性,15次循环后的转换率为对照组的1.65倍.表征结果显示,最佳掺杂比例的CaCO3-TiO2复合储热材料具有更小的粒径和更发达的孔隙,因而在循环过程中具备更好的抗烧
简要介绍了美国濒海战斗舰研制情况,评述了濒海战斗舰用主壳体用材,介绍了铝合金主壳体材料的合金种类、应用部位、材料规格及材料用量,确定了铝合金壳体材料的腐蚀保护涂料体系、外加电流保护等方案,并介绍了美国在舰船用铝合金方面近期的研究动向.
The unique hot carrier-driven direct plasmonic photocatalysis of coinage metal nanomaterials (NMs) via energetic localized surface plasmon resonance (LSPR) in visible-light region has been explored in recent years.However,the low photoinduced electron tra
Although a variety of processing routes were developed to in-situ manipulate microstructure for fabri-cating high-performance Ti-6Al-4V alloy by directed energy deposition (DED),the in-situ microstructural control ability has been limited and lead to a na
研究了硅酸钠对碱性低氢焊条性能的影响.试验结果表明,适当增加药皮中的硅酸钠含量,可使焊条套筒长度减小,熔渣黏度减小,立焊笔尖倾向减小,飞溅稍微增大,而焊条熔敷金属的化学成分、力学性能和扩散氢含量的变化则不明显.故可以通过调整碱性低氢焊条药皮中硅酸钠的含量来优化焊接工艺性.