【摘 要】
：
Mg-3Al-1Zn alloy sheets have been deformed by continuous bending (CB) to investigate the effects of processing parameters (bending angle and repetitive passes) on the texture and formability.The samples exhibited a bimodal microstructure with abnormal gro
【机 构】
：
State Key Laboratory of Mechanical Transmission, College of Materials Science and Engineering, Chong
论文部分内容阅读
Mg-3Al-1Zn alloy sheets have been deformed by continuous bending (CB) to investigate the effects of processing parameters (bending angle and repetitive passes) on the texture and formability.The samples exhibited a bimodal microstructure with abnormal growth grains in the surface region and fine grains distributed in the center after CB process followed by annealing.The texture evolution measured by XRD indicated that the basal poles were rotated from ND toward RD,and the texture intensity decreased with the bending angle decreasing and repetitive passes increasing.Compared with the as-received sample,the yield strength of CBA-120-2 sample significantly decreased from 183 to 112 MPa,and a smaller r-value and a larger n-value were obtained.The formability of CB processed samples in annealing condition was significantly enhanced with the highest of Erichsen value of 5.4 mm,increased by about 135％.The improvement of formability was likely attributed to the weakened and RD-tilt basal texture and coarse grains in the surface part.
其他文献
Self-lubricating copper matrix composites reinforced with graphene were prepared by electroless plating and powder metallurgy.The morphology and structure of graphene,Cu@graphene powder,and Cu@graphene/Cu composites were characterized and the tribological
In this review paper,the research progress on corrosion behavior of hexagonal close-packed (HCP) singular phase,body cubic-centered (BCC) singular phase and (HCP + BCC) duplex-structured Mg-Li alloys has been summarized and reviewed,and the future trend a
Particle reinforced magnesium matrix composite (PMMC) possesses the merits of high specific strength,high specific modulus,better dimensional stability,good wear resistance and lower production cost,which is thought as a promising material in the field of
Novel crystallization behaviors of Zr55Cu30Al1oNi5 bulk metallic glass are investigated.On the one hand,mixed oxides,including CuO,CuAlO2,CuAl2O4 and ZrO2,show sequential oxidation process determined by coupling effects of specific cyclic load and tempera
The defects created in commercial dental alloys during blasting with alumina particles propelled in compressed air under pressure 0.1 and 0.4 MPa have been studied using positron annihilation spectroscopy,scanning electron microscopy and X-ray diffraction
A series of Ti2ZrHf0.5VNbx (x =0,0.25,0.5,0.75 and 1.0) refractory high-entropy alloys were prepared to investigate the alloying effect of Nb on the microstructures and mechanical properties.All the alloys displayed a simple BCC structure.The microstructu
The development of high-entropy alloys (HEAs) has stimulated an ever-increasing interest from both academia and industries.In this work,three novel MoNbFeCrV,MoNbFeCrTi,and MoNbFeVTi HEAs containing low thermal neutron absorption cross section elements we
This paper presents a new thermomechanical model of friction stir welding which is capable of simulating the three major steps of friction stir welding (FSW) process,i.e.,plunge,dwell,and travel stages.A rate-dependent JohnsonCook constitutive model is ch
A calculation method based on a combination of △g parallelism rule,good matching site (GMS) analysis,CSL/DSCL (coincidence site lattice/displacement shift complete lattice) and the O-lattice theory has been applied to interpret the observation of the habi
In pressurized water reactor,fretting corrosion has become the main reason for the failure of 690TT heat exchanger tubes.The effect of temperature on the fretting corrosion behavior between 690TT tube and 405 stainless steel (SS) bar has been studied duri