PEPS车辆启动电路可靠性设计及研究

来源 :第19届亚太汽车工程年会暨2017中国汽车工程学会年会 | 被引量 : 0次 | 上传用户：laoyang2009123456

【摘要】

：

本文从传统点火开关车辆与PEPS车辆两者在结构、电气原理上的差异性着手分析,重点介绍PEPS车辆启动可靠性设计的几个要点,包括整车布置、启动电路设计、堵转保护、超时机制等,并通过概率计算,启动系统安全性得到显著提高,启动故障的典型情形得到控制.本文探讨的内容,对PEPS车型启动回路设计开发具有一定的借鉴意义.

【作者】

：

张启明吴泽民王月张爽舒

【机构】

：

东风汽车公司技术中心电子电器部东风格特拉克汽车变速箱有限公司产品研发部

【出处】

：

第19届亚太汽车工程年会暨2017中国汽车工程学会年会

【发表日期】

：

2017年7期

【关键词】

：

PEPS车辆启动电路可靠性设计安全风险

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

其他文献

An Improved Method of CMS and Applied into Calculation of Vehicle’ s Substructure

A new improved component mode synthesis(CMS)technology based on free-interface mode reducing method is investi- gated. Connection conditions between sub-structures, which is one of the essential influ

会议

component mode synthesissubstructureselastic/ rigid connectionmodaltransmiss

A Study on Beat-rattle Phenomenon of Manual Transmission

The paper provides an investigation into the beat-rattle occurring on a RWD manual transmission at high gear position and under wide open throat condition. Firstly, the sources of beat-rattle are disc

会议

beat frequencyrattleeccentricityfrequency differencetorsional vibration

A Predicted Method of the Exhaust Hanger Location Design in the Vehicle

An ideal location of the exhaust hanger can reduce the transmission of the vibration and noise to the vehicle body, which is beneficial for the NVH performance of the vehicle. Based on the finite elem

会议

exhaust systemhanger locationDisplacement Normalization Method (DNM)Average D

Research on Vehicle Rear Door Shake of a Certain SUV Based on TPA

The problem of the abnormal sound of the car body closure seriously affects the ride comfort. In order to solve the prob- lem of rear door shake of a SUV driving on the washboard road, transfer path a

会议

abnormal soundtransfer pathclosureCAE

The Solutions and Study on Lifting and Falling Noise for Car Door Glass

Based on the theory of equivalent radiated power of panel, the performance of equivalent radiated power of the door pan- el under the unbalanced centrifugal force excitation of the elevator motor is c

会议

doorglass lifting and fallingnoiseEquivalent Radiated Power

某四缸汽油发动机排气歧管--催化器总成断裂失效问题研究

本文介绍了某四缸汽油发动机排气歧管———催化器总成出气端锥与尾管连接处断裂的原因分析和改进过程.通过失效故障树分析方法排查原因,再运用仿真和试验相结合的手段,进行问题查找分析和改进效果确认,最终确定了失效的根本原因,制定出新颖有效的改善方案,解决了排气歧管———催化器总成断裂失效问题.改善后的零件已经顺利通过所有发动机耐久性考核试验.

会议

汽车四缸汽油发动机排气歧管催化器总成断裂失效故障树分析

一种基于时变内模的PMSM-EPS助力纹波抑制方法

本文研究了汽车EPS系统的助力纹波问题,提出一种基于时变内模控制的助力纹波抑制方法.抑制助力纹波的意义在于提高EPS系统性能、改善驾驶人手感.功率开关器件死区、管压降和电动机齿槽转矩会造成PMSM转矩脉动.该扰动信号本质上是基于转角周期变化的,但当转向盘转速变化时,对时间却是非周期性变化的.本文讨论了将EPS助力纹波问题与基于转角变化系统的跟踪控制问题相联系的方法.文中使用一种时变内模控制器设计来

会议

汽车电动助力转向系统助力纹波抑制方法时变内模

天然气发动机喷气电磁阀驱动模块的研究与实现

针对天然气发动机喷气电磁阀在低温环境下开启困难问题,设计了低成本,高可靠性的喷气电磁阀驱动模块.在对各个因素综合分析的基础上,采用单电源单边驱动方式,各个驱动通道相互独立,保持电流通过硬件脉宽调制(PWM)反馈控制,根据驱动电流上升速率实现喷气电磁阀驱动回路的故障诊断.在车辆冷起动工况时,喷气电磁阀驱动电流波形从正常驱动电流波形切换到冷起动驱动电流波形,通过提升驱动电流波形的峰值电流,提高喷气电磁

会议

汽车天然气发动机喷气电磁阀驱动模块冷起动故障诊断

Redundant Design And ASIL Decomposition for Escl Functional Safety Development According to ISO 2626

The importance of functional safety design has been widely discussed all over the world, the application of most of E/E system increased rapidly, and it consists a large number of ECUs, sensors and ac

会议

ESCLfunction safetyredundancy designISO 26262

The Study about Piston Pin Noise of Full Floating System in the Internal-Combustion Engine

This study aims at the mechanism of piston pin noise of full floating system and resolving the piston pin noise problem at hot idle condition. The piston pin noise sounds like ticking noise, and gener

会议

NVHticking noisewavelet analysismulti body dynamicsEHD Analysis

PEPS车辆启动电路可靠性设计及研究

与本文相关的学术论文