【摘 要】
：
Anatase TiO2 particles of about 20 nm in the diameter were successfully synthesized with Ti(SO4)2 as titanium source and stronger ammonia water as precipitant at 240℃ for 48 h with pH=5 using the hydr
【机 构】
：
The 3rd Department of Suqian College, Suqian, Jiangsu, China, 223800
【出 处】
：
2011中国功能材料科技与产业高层论坛
论文部分内容阅读
Anatase TiO2 particles of about 20 nm in the diameter were successfully synthesized with Ti(SO4)2 as titanium source and stronger ammonia water as precipitant at 240℃ for 48 h with pH=5 using the hydrothermal hydrolysis method.The samples were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM).TEM analysis confirmed that the influence of the increase of the pH value on the size of as-prepared TiO2 particles became remarkably fine.However,with the further increase of the pH value,the influence of the increase of the pH value on the size of TiO2 particles was not obvious.And ultraviolet-visible absorption spectroscopy (UV-VIS) results showed that the size of Anatase TiO2 nanoparticles became small was propitious to the blue shift of their absorption peak.
其他文献
Anisotropic nano-crystalline Nd-Fe-B magnets were prepared by applying the MQ-C melt-spun powders and the technique of hot-pressing (HP) and hot-deformation (HD).The change of magnetic proper ties and
嵌段共聚物聚己内酯-聚N-异丙基丙烯酰胺(PCL-b-PNIPAM)是通过阳离子开环聚合(ROP)和可逆加成-断裂链转移聚合(RAFT)合成,并利用α-CD和PCL-b-PNIPAM的包结络合作用,自组装成α-CD-PCL-b-PNIPAM包络物.用傅里叶红外光谱(IR)、核磁共振(1HNMR)和凝胶色谱(GPC)对反应产物进行了表征,证明成功制得了预定结构产物.热性能用热重(TGA)和差示扫描量
作为第三代半导体材料的代表，GaN基半导体材料因有宽的直接带隙，高的击穿场强，高的热导率和非常好的物理、化学及热稳定性，成为制备短波长光电器件、高温器件和高频大功率器件的首选材料，采用基于密度泛函理论的第一性原理超软赝势方法,在局域密度泛函近似下,计算了Mn和Mn-Cd掺杂纤锌矿GaN的电子结构、光学和磁学等性质.结果表明:掺杂后体系均在能隙深处产生自旋极化杂质带,表现为半金属性,适于自旋注入,与
在凝固过程中通过施加不同强度直流磁场来制备MlNi3.4Co0.75Mn0.4Al0.25B0.2储氢合金.采用XRD、恒流充放电及交流阻抗(EIS)对所制取的样品进行测试和表征.结果表明:合金均具有CaCu5型六方结构的同时出现了少量CeCo4B第二相,且随磁场强度增大合金第二相含量增加.磁场处理使合金的初始放电容量与活化性能有所提高,但电化学容量有所下降,合金的高倍率放电和低温放电容量随磁场强
采用碱法改性粉煤灰来处理铅酸蓄电池厂的硫酸雾,研究了NaOH溶液浓度、改性温度、v(粉煤灰)/V(NaOH溶液)、改性时间、孔隙率对酸雾去除效果的影响.结果表明,当NaOH的浓度为3mol/L,温度为120℃,V(粉煤灰)N(NaOH溶液)=1∶10,孔隙率为14％,改性时间为5h时,硫酸雾去除率最高可达95％,改性后的粉煤灰对酸雾的去除率比改性前整体提高了30％.
随着材料合成技术的进步,各种新型的气敏材料被不断地开发报道,这些材料通常具有高的比表面积、有序的孔道分布、良好的电信号传输能力等特点,因此表现出高灵敏度、快响应恢复及良好的稳定性、选择性等性质,从而成为了气敏研究的热点.本文比较了使用不同的测试方法所获得的同种气敏材料的性能参数,分析了造成这些差异的原因,从而为针对新型气敏材料的性能测试提供了参考.
制备了三组重晶石水泥基材料,并对三组材料对14.8MeV快中子的衰减效应进行了测试,结果表明:重晶石水泥基材料与空白组相比,8mm厚时,对14.8MeV快中子的衰减比略微有上升趋势,40mm厚时,对14.8MeV快中子的衰减比略微有下降趋势;随着重晶石含量的增加,特别是40mm厚样品对14.8MeV快中子的衰减比有明显增强效果;所有样品随着样品厚度的增加,对14.8MeV快中子的衰减比有增大的趋势
The molecular dynamics simulation studies on the microstructure evolution properties of liquid Ca-Mg alloys during the rapid solidifications have been performed.The simulated structure factor S(q) of
本文以聚碳硅烷(PCS)为原料,采用静电纺丝技术制备了β-SiC/SiO2微米纤维,着重探讨了在料液中添加四丁基溴化铵/N,N-二甲基甲酰胺(TBAB/DMF)溶液对前驱体纤维形貌的影响,优选了前驱体的不熔化处理时间,研究了β-SiC/SiO2纤维的光致发光性能.采用扫描电镜(SEM)、傅立叶红外光谱(FT-IR)、X射线粉末衍射(XRD)和光致发光光谱(PL)等测试手段对产物进行了表征.结果表明
P-type Bi0.5Sb1.5Te3 thermoelectric crystals with various percentage of Te (x=0.00-3.00 wt.%) were prepared by gradient freeze method.By doping Te content differently and fabrication processes,the ant