Development of Polymer Based Electromagnetic Shielding Materials

来源 :The 11th China-Japan joint conference on Composite Materials | 被引量 : 0次 | 上传用户:q418004922
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
  The development of EMI shielding materials is receiving increasing attention recently since the higher speed communication resulted in the higher frequency range of electromagnetic waves and this will produce electromagnetic interference (EMI) to electronic instruments and even to human body.
其他文献
Aluminum-polyphenylene sulfide single lap joints were prepared by aluminum pitting corrosion.The joint strength was estimated in relation to structural information measured using scanning electron mic
In this study,effect of hot water treated rice straw on the mechanical properties of rice straw/poly (lactic acid) (PLA) composite was investigated.The optimal treated condition was observed by changi
One of the most important issues for the design of filament-wound pressure vessels reflects on the determination of the most efficient meridian profiles and related iber architectures.
本文使用硅烷偶联剂KH550对介孔分子筛MCM-41进行表面修饰后添加到环氧树脂中,制备得到环氧树脂/MCM-41复合材料。采用热分析、扫描电镜、傅里叶红外光谱、X衍射、氮气吸附-脱附等手段对表面修饰前后的MCM-41进行结构表征,并对复合材料的力学、热学和电气性能进行测试。本文利用差示量热扫描仪熏点研究了环氧树脂/MCM-41复合材料的固化动力学,通过n级模型得到复合材料固化过程的反应级数、活化
会议
通过熔融共混法制备聚乳酸(PLA)/聚对苯二甲酸-己二酸-l,4-丁二醇共聚酯(PBAT)/有机蒙脱土(OMMT)三元共混物,研究了不同加工条件下,蒙脱土纳米粒子对共混物微观形貌的影响,并结合纳米粒子选择性分布效应对其增容机理进行了初步探时。
采用超声波辅助搅拌铸造的方法,成功制备了碳化硅质量分数为20%的大尺寸镁基复合材料,铸锭的质量大约为21千克.与基体合金相比,复合材料的力学性能得到了明显提升.在复合材料的不同位置,碳化硅颗粒均匀分布,各部位的含量相同.但是,从微观结构上来看,颗粒沿着晶界呈项链状分布.在热挤压过程中,尽管部分碳化硅颗粒结构受损,但是显著改善了碳化硅颗粒在复合材料内的分布,同时进一步提高了材料的力学性能.T6处理材
使用高韧性环氧树脂R608通过RTM工艺制备了M40级碳纤维缝编织物/环氧复合材料。对M40级碳纤维缝编织物/环氧复合材料进行-196℃到80℃冷热循环试验,并对其100次和300次冷热循环前后力学性能和微观形貌进行了测试。结果显示,100次冷热循环后,拉伸性能、弯曲性能、压缩性能、层间剪切和冲击性能略微增加或降低,而300次冷热循环后,这些力学性能基本趋于稳定。总的来说,与冷热循环前相比,M40
Multiwalled carbon nanotubes/Polycarbonate (MWCNTs/PC) nanocomposit-es were successfully prepared by injection molding process.With the injection conditions changed,MWCNTs/PC nanocomposites with diffe
采用聚乙二醇(PEG)改性的聚丁二酸丁二醇酯(PEG/PBS)分别与羧甲基纤维素(cMc)和羟乙基纤维素(HEC)共混制备了在水相均匀分散的聚酯/纤维素新型液体复合材料,并结合分子模拟技术对该液体复合材料间的相互作用机制进行了研究。
In the present study,according to the viewpoint of the formation mechanism of the internal microstructure of the nanocomposites samples in the injection molding,the effects of the contents of carbon n