【摘 要】
:
The technology of sintering flue gas dry desulphurization is a common domestic desulphurization technology in metallurgical industry,however handling the ash of sintering flue gas dry desulphurization
【机 构】
:
Shanghai Meishan Iron & Steel Co.,Ltd.,Nanjing 210039,Jiangsu,China
论文部分内容阅读
The technology of sintering flue gas dry desulphurization is a common domestic desulphurization technology in metallurgical industry,however handling the ash of sintering flue gas dry desulphurization is a baffling problem.In light of coexistence of dry and wet desulphurization in Meigang and surplus wet desulphurization ability,reuse of ash of sintering flue gas dry desulphurization as flux in the sintering machine in which wet desulphurization process is used is put forward,which can not only use CaO in dry desulphurization ash,but also convert S in dry desulphurization ash into gypsum through wet desulphurization device.Results by sintering pot show that,if specific proportional dry desulphurization ash is added to sintering proportion,the strength of sintering ore can be increased slightly,metallurgical performance can be improved appropriately,fuel consumption can be increased slightly,but the content of Sulphur in sintering ore increases slightly;Industrial test results show that,if 1.5% desulphurization ash is added to sintering proportion,sintering ore tumbler strength cannot be affected,metallurgical performance of sintering ore can be improved appropriately;the content of Sulphur in sintering ore increases 0.003%,fuel consumption can be increased to some extent.Dry desulphurization ash can be converted into gypsum effectively,the content of Sulphur in wet desulphurization flue gas will not go beyond the limit,the reuse of dry desulphurization ash returned to sintering is feasible.Through preliminary estimates,there will be good society and economic benefits.
其他文献
与热轧电工钢带相比,冷轧电工钢带具有磁感高、铁损低、表面光滑和平整、厚度均 匀性好、冲片效率和叠片系数高等优点,被广泛应用于制造各种发电机、电动机和变压器等.攀钢生产的冷轧无取向电工钢主要供家电企业用于制造电机定转子.初期生产的电工钢带由 于横向厚差过大,达到30 μm左右,超出了用户对电工钢带的订货技术要求,导致叠片系数不能满足用户使用要求,此现象主要集中在带钢的边部,用户对此提出质量异议,影响
结合工业化生产的无取向硅钢,进行了RH精炼喂CaSi线实验研究。针对不同的 钙处理条件,观察了夹杂物的形貌和尺寸分布,探讨了钙处理后钢中的夹杂物变化规律.结果表明,实验条件下,钙处理可以有效抑制MnS、AIN夹杂物的生成,有效促进钢中微细夹杂物 的聚合、上浮、去除,钢质纯净度明显提高.经过合适的钙处理后,钢中的夹杂物以独立存在的Ca0为主,同时有少量含CaO、Sio2、MgO的复合夹杂,没有发现C
The microstructure and texture evolution of Fe-3.2qo Si non-oriented silicon steel fabricated by twin-roll casting was investigated.Temperature and strain gradient during casting cause through-thickne
采用多弧离子溅射技术在27Q130取向硅钢表面沉积高硅FeSi合金层,退火处理后两者有机结合成为高硅梯度硅钢。利用XRD、SEM和EDS对高硅梯度硅钢表面FeSi合金层的结构、形貌、成分和织构进行了分析。结果表明:高硅梯度硅钢表面的高硅FeSi合金层为致密多晶层,其硅质量分数超过6.5%,厚度介乎8~20 μm,两者结合紧密;沉积态的表面高硅FeSi合金层具有强烈的{110}面织构(<110>∥N
首先介绍了我国钢铁产业现状及钢铁行业CO2排放情况,分析了我国钢铁行业CO2减排的必要性和紧迫性.然后对二氧化碳捕集与封存(CCS)技术进行了介绍.最后以宝钢集团为例,分析了应用CCS技术对钢铁行业排放的CO2进行减排的可行性与潜力.研究结果表明,我国是世界上最大的钢铁生产和消耗国家之一.随着社会经济的发展,我国钢铁需求和产量显著增加,直接结果是CO2排放量的增长迅速,2009年我国钢铁行业CO2
双膜法用于钢铁工业废水处理,近年来在大型钢铁企业应用日益广泛,但是,由于钢铁废水成分复杂,应用中存在两大难题,一是反渗透机组污堵速度快,二是反渗透膜产水通量下降严重且常规酸碱清洗无法恢复,导致反渗透膜使用寿命短,造成双膜法处理钢铁废水成本高,制约了双膜法处理钢铁废水的推广.通过对反渗透膜面污染物和废水污染成分分析,得出双膜法处理钢铁废水工艺中,反渗透膜污堵性质主要是微生物和有机物污堵,尤其是分子量
Steelmaking slag is one of the main by-products generated from steelmaking process.It has been utilized such as the raw material of road bed,various civil engineering and fertilizer so far.However,it
烧结废气温度偏低、废气量大、污染物含量高且成分复杂,是钢铁行业低温余热利用和废气治理的难点和重点,已引起国内外的广泛关注.近年来,宝钢依托国内首套烧结废气循环工业试验装置,针对烧结废气的特点,在循环烧结工艺系统设计和优化、二噁英类污染物源头抑制、循环烧结配矿优化、循环风机和管道耐磨设计、高效除尘设备开发、系统联动控制和稳定运行技术、烟气混合和切换、循环烟罩密封、风量氧量调节、热风循环烧结工艺控制和
焦炉使用寿命可长达20-25年,最长可达40年,以致对其用后耐火材料的研究机会十分难得.对硅砖在焦炉作业条件下的显微结构演变情况还缺乏深入的分析.因此,了解焦炉作业过程中硅砖显微结构变化将为炉体检修、维护和焦炉设计提供参考依据.梅钢焦炉已使用了31年,炉况基本良好,还可维持生产,但因易地扩建而拆除.借此机会选取了3个炭化室残砖进行了微观结构分析.焦炉用后硅砖的微观结构分析表明,炭化室或多或少存在残
Steel is at the core of a green economy,in which economic growth and environmental responsibility work hand in hand.Over 1.5 billion tons of steel are manufactured and used every year and it will cont