Synthesis of novel europium complexes and their photoluminescence properties

来源 :稀土学报(英文版) | 被引量 : 0次 | 上传用户:bobogu
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Two novel luminescent Eu(Ⅲ) complexes with the formulas (NIP)Eu(DBM)3 1 and (ENIP)Eu(DBM)3 2 (NIP=2-(naphthalen-1-yl)-1H-imidazo [4,5-f] [1,10] phenanthroline,ENIP=1-ethy1-2-(naphthalen-1-yl)-1H-imidazo [4,5-)] [1,10] phenanthroline,DBM=dibenzoylmethanato) were successfully synthesized and characterized by IR and elemental analysis.The UV-vis absorption spectra and photoluminescence properties of the complexes were investigated,and the irradiation at the absorption band between 300-400 nm of europium complexes either in solution or in the solid state led to the emission of a sharp red band at ~610 nm,a characteristic Eu3+ emission due to the transition of5D0→7F2.Furthermore,the weak emission bands around 587 and 595 nm attributed to 5D0→7F0 and 5D0→7F1 transition were also displayed in the emission spectra.These results demonstrated that the Eu(Ⅲ) ion was sensitized efficiently by the ligand and displayed photoluminescence with high intensity,narrow half-peak width,and monochromic light.The excited-state lifetimes of 1 and 2 were in the microsecond time scale,but the photoluminescence quantum yield of 2 (0.03) was two times higher than that of 1 (0.01) which should be attributed to the effect of the ethyl substituting in ENIP.
其他文献
对铝合金板料7075在加热状态下的成形性能进行研究.首先,通过单向拉伸试验得到不同温度以及不同应变速率下的应力一应变关系.然后,通过极限拉伸比(LDR)试验和极限拱顶高(LDH)
在温度为943 K的LiCl-KCl-KF熔盐体系中添加不同浓度的La2O3和MgCl2直接电解制备Mg-Li-La合金.运用X射线衍射分析、扫描电子显微镜及能谱分析和金相显微镜对所得合金进行分析
Good ignition-proof principle and mechanical properties were realized in Mg-Y-Ca-Zr alloy system.By adding Y and Ca elements,the ignition point of Mg-3.5Y-0.8Ca
随着大型影剧院、体育馆、音乐厅、会展中心、候机楼、大卖场、图书馆、科技馆等建筑物的增多,灭火工作备受瞩目。毕竟这些地方是人群较密集的地方,再加上结构特殊,防火分区
为了提高铝合金对激光的吸收率,改善焊缝表面成形,对1.8 mm厚的6013铝合金板进行活性剂CO2激光焊接.活性剂主要采用的是对激光具有较高吸收率的氧化物和氟化物,将其焊前预涂
A cone-shaped gadolinium doped ceria (Ce0.9Gd0.1O1.95,GDC) electrolyte cylinder with a thin wall was fabricated using slip casting technique.The diameter of the
目的:探讨心血管介入诊疗中影响术者辐射防护与安全的相关因素并对术者的放射防护提出的相关建议。方法:使用多用剂量、TLD剂量片和头胸腹拟人模体分别测定术中术者所站立的
利用电刷镀工艺在316L不锈钢上制备了结合力良好的钯膜.使用扫描电子显微镜、X射线能谱、X射线光电子能谱(XPS)、质量损失实验和电化学测试研究了膜层的性能.结果表明,电刷镀
比较研究了Mg-3Ce- 1.2Mn-0.9Sc和Mg-3Ce- 1.2Mn-1Zn镁合金的铸态组织和力学性能.结果表明:含Sc合金主要由α-Mg、Mg12Ce和Mn2Sc相组成,而含Zn合金则主要由α-Mg和Mg12Ce相组
The humidity sensitive characteristics of the sensor fabricated from Ce-doped nanoporous ZnO by screen-printing on the alumina substrate with Ag-Pd interdigital