Enhancements of Passive Film and Pitting Resistance in Chloride Solution for 316LX Austenitic Stainl

来源 :金属学报(英文版) | 被引量 : 0次 | 上传用户:soochow_deer
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
In the present work,the electrochemical behavior and properties of the passive film of a new Sn-alloyed 316LX austenitic stainless steel were investigated.With the increase in Sn content in 316LX austenitic stainless steel from 0 to 0.21%,the critical pitting temperature value increased from 32.6 to 38.8 ℃,and the pitting potential increased from 0.252 VSCE to 0.317 VSCE.Electrochemical impedance spectroscopy results showed that the corrosion resistance of passive film rose with the increase in Sn content,indicating a more stable passive film.The Mott-Schottky measurement revealed an n-type passive film with a decreased carrier concentration on the 316LX austenitic stainless steel surface.The Cr,Sn2+ and Sn4+ (SnO,SnOHCl or SnO2) enrichments were observed in the passive layer by X-ray photoelectron spectroscopy.The enrichment of Sn and Cr in the passive film can account for the enhanced pitting resistance of 316LX austenitic stainless steel in chloride solution.
其他文献
Single-pass compression tests were performed to investigate the hot deformation behavior of low-carbon boron microalloyed steel containing three various vanadium contents at 900-1100 ℃ and strain rate of 0.01-10 s-1 using the MMS-300 thermal mechanical si
Hot deformation behavior of 0.3C-15Cr-1Mo-0.5N high nitrogen martensitic stainless steel (HNMSS) was investigated in the temperature range of 1173-1473 K and at strain rates of 0.001-10 s-1 using a Gleeble 3500 thermal-mechanical simulator.The true stress
In this paper,we report the fabrication of the photocatalysts composed of Cu2O nanobelts and nanoporous Cu (NP Cu) substrate,which is obtained by soaking the NP Cu in dehydrated ethanol.The NP Cu substrate is achieved by dealloying of Ti40.6Zr9.4Cu40.6Ni6
Three-dimensional distribution of solute elements in an Mg-Zn--Gd alloy during ageing process is quantitatively characterized by three-dimensional atom probe (3DAP) tomography.Based on the radius distribution function,it is found that Zn-Gd solute pairs i
To explore the optimum use of stabilised elements and study the influences of stabilisation in 18Cr-2Mo grades,the Nb and Nb + Ti microalloying investigation focused on the relationships of the microstructure and mechanical properties of the microalloyed
Rutile (TiO2) particle-reinforced aluminum matrix composites were prepared by friction stir processing.The microstructure was studied using conventional and advanced characterization techniques.TiO2 particles were found to be dispersed uniformly in the co
In this research,2205/Q235B clad plates were prepared by a vacuum hot rolling composite process.The effects of adding Fe,Ni,and Nb interlayers on the bonding interface structures and the shear strengths of the clad steel plates were studied.The results sh
Coarsening of cuboidal γ\'precipitates and relevant diffusion process in Ni-based single-crystal superalloy CMSX-4 were investigated at 1000,1020 and 1040 ℃ for specific times.The γ\'coarsening kinetics followed a cubic rate law with time and was pres
The microstructure and mechanical properties of NiCrMoV-and NiCrSi-alloyed medium-carbon steels were investigated after multiple tempering.After austenitising,the steels were hardened by oil quenching and subsequently double or triple tempered at temperat
To understand the atomistic mechanisms of tension failure of Ni-based superalloy,in this study,the classical molecular dynamics (MD) simulations were used to study the uniaxial tension processes of both the Ni/Ni3Al interface systems and the pure Ni and N