污泥水分含量对其空气气化特性的影响

来源 :燃料化学学报 | 被引量 : 0次 | 上传用户:liongliong467
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
利用外热式下吸固定床气化实验装置,研究了在一定的空气流量(0.05m3/h)、气化温度(800℃)下污泥水分含量对3种不同性质污泥空气气化特性的影响.结果表明,气化气中CO2、CH4和H2含量、气化气热值以及水相生成量均随污泥水分含量的增加而增加,而CO含量和焦油生成量呈降低趋势.污泥厌氧消化使气化气中CO、CH4、H2、CmHn含量以及气化气品质降低;而污水处理工艺中的厌氧过程可改善气化气品质,其中来自A2/O工艺消化污泥的气化气品质高于普通活性污泥法消化污泥的气化气品质.随着污泥水分含量的增加,2种不同污水处理工艺产生的消化污泥气化气中CO、CO2和H2含量的差距逐渐加大,来自于同一A2/O工艺的消化与未消化污泥气化气中H2 和CO2含量的差距亦逐渐加大,而消化与未消化污泥气化气中CO含量的差距则逐渐接近.“,”The properties of gasification for three kinds of sewage sludges with different moisture contents are studied in an external heated downdraft reactor under a stable air flux of 0.05m3/h and a constant gasification temperature of 800℃. The results show that the contents of CO2, CH4 and H2 in gas, lower heating value (LHV) of gas and aqueous yield increase with increasing moisture content, while content of CO and tar yield decrease. Sludge anaerobic digestion process increases the contents of CO, CH4, H2 and CmHn in gas and reduces the quality of gas. The anaerobic process in wastewater treatment can improve the quality of gas. The quality of gas produced by gasification of anaerobic digestion sludge from A2/O process is higher than that from activated sludge process. With increasing moisture content in sludge, the difference in the contents of CO, CO2 and H2 in the gas produced by both anaerobic digestion sludge gasification is gradually increased, and the difference in the contents of CO2 and H2 produced by the gasification of digested and undigested sludges from the same A2/O process is also increased, while the difference in CO content is gradually reduced.
其他文献
综述了Al2O3颗粒增强钢铁基复合材料的研究进展,重点介绍了几种复合工艺方法及其特点,分析了当前研究的不足,并对未来的发展进行了展望。 The research progress of Al2O3 p
请下载后查看,本文暂不支持在线获取查看简介。 Please download to view, this article does not support online access to view profile.
期刊
综述了微弧氧化-水热处理法钛合金表面活化技术的发展状况、原理及其影响因素;系统分析了微弧氧化-水热处理法制备羟基磷灰石技术的优点以及现阶段存在的问题;并对微弧氧化-
通过对45钢基体表面等离子喷涂Al2O3-13wt%TiO2(AT13)涂层和Al2O3涂层进行对比试验。结果表明:涂层组织呈明显的层片状结构,并含有孔隙、微裂纹及未熔颗粒等缺陷,基体与粘结
采用正交试验法研究了激光熔敷对304不锈钢基体上Co-Al-W合金熔敷层质量的影响,通过极差分析和方差分析,评价了激光熔敷工艺参数对熔敷层质量影响的显著程度,并对激光熔敷工
综述了TiA1N硬质涂层的结构、性能,以及以TiA1N为基的多元涂层和纳米技术涂层的国内外最新研究现状.对TiA1N涂层进行多元化、多层化以及纳米技术的应用是提高该涂层综合性能
以常规和纳米团聚体ZrO2-7%Y2O3陶瓷粉末为原料,采用等离子喷涂和等离子喷涂+激光重熔复合工艺在TiAl合金表面制备了常规和纳米结构热障涂层。用扫描电镜(SEM)分析了粉末结构
用不同工艺参数的强流脉冲离子束技术对钛基压气机叶片进行表面轰击,对离子束诱发的表面形貌进行分析。结果表明,强流脉冲离子束辐照在钛合金表面形成尺寸约为几至几十微米的
利用脉冲偏压磁过滤电弧离子镀在高速钢(M2)基底上沉积了厚约2.5μm的TiN薄膜;分别采用FESEM、GDOES、XRD和划痕试验法观察薄膜表面和断面形貌、测试薄膜成分及相结构,分析膜