【摘 要】
：
Using theoretical simulations for optical fiber surface plasmon resonance (SPR) sensors and prism-based SPR sensors coated with negative permittivity material (NPM), we investigated the effect of the permittivity of NPM on the transmitted spectrum of opti
【机 构】
：
NationalEngineeringLaboratoryforFiberOpticSensingTechnology,WuhanUniversityofTechnology,Wuhan430070,
【出 处】
：
ChineseOpticsLetters
论文部分内容阅读
Using theoretical simulations for optical fiber surface plasmon resonance (SPR) sensors and prism-based SPR sensors coated with negative permittivity material (NPM), we investigated the effect of the permittivity of NPM on the transmitted spectrum of optical fiber SPR sensors and the reflected spectrum of prism-based SPR sensors and then obtained optimum permittivity of the NPM, which can excite the sharpest SPR spectrum in the white light region (400–900 nm).
其他文献
The limitation of paraxial condition of paraboloid refracting system in performing fractional Fourier transform acts like an aperture, which makes the system different from ideal systems. With aperture expanded as the sum of finite complex Gaussian terms,
菲利浦公司制造的GAL-450型GaAs注入式光激射器包括液氮冷却的眞空杜瓦瓶，冷却温度为77 °K。当杜瓦瓶内温度降到65 °Κ时，产生激光的闼值减小30%,相应地波长也减小40埃。
AlGaN-channel high electron mobility transistors (HEMTs) were operated as visible- and solar-blind photodetectors by using GaN nanodots as an optically active floating gate. The effect of the floating gate was large enough to switch an HEMT from the off-s
虽然研究人员对科学技术的发展作了很多努力，但光学材料的发展是靠需要和科学好奇心来推动的。从彻利略的望远镜到当今的激光核聚变，每前进一步都从可行的光学材料开始。新发展确定了新需要，进而推动材料的发展。明年，朗缪尔-布洛杰特薄膜和读写光学存储装置的应用将达到商品化。
高分辨率大视场成像使得航天遥感可以在更广阔的范围内进行更精细的感知,提出一种基于计算成像基本原理的大视场次优计算成像设计方法。该方法将成像过程分为硬件成像和软件复原两方面,软硬件结合的设计方法可以充分结合二者优势,降低了硬件设计难度,提升了系统成像综合性能。在光学系统硬件设计方面,提出次优光学设计方法,不再将设计自由度资源单一应用在小视场范围内,而是在更大视场范围内寻求一致性的次优点扩展函数,结合
本文指出了钕激活的玻璃光受激发射在闪光过程中振荡光谱线的数目以及它们的波长随时间的变化。斯奈泽(E. Sixitzer)的文章曾经指出钕激活玻璃受激光发射，由分布在1.061~1.062微米波段的光谱线组成。
A laser micromachining technique for the fabrication of metallic microstructures is proposed. The fabrication of microstructures is done by laser-induced wet etching that adopts an optical fiber as a machining tool. The laser beam delivered through the mu
通过多个点状探测器在三维空间中的适当分布的排列, 得到了基于倒置结构X射线锥形束投影的直接体积重建三维成像模式。 与锥形束边界重建相结合, 针对倒置结构构造的重建算法及其数值仿真表明, 新的成像模式相对于传统的锥形束边界重建, 在实际存在X射线投影噪声情形下有明显的优点。
利用光纤激光器在超硬刀具表面开展了微沟槽加工试验, 研究了激光工艺参数对微沟槽表面形貌的影响。研究结果表明, 通过激光工艺参数的优化, 能够获得尺寸均匀、形貌良好的微沟槽阵列, 实现了对超硬刀具表面微沟槽形貌的有效控制。