岩石孔隙度在内生矿床成矿中的作用

来源 :地质与勘探 | 被引量 : 0次 | 上传用户:aolongjiutian
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
岩浆期后矿床,不论围岩的蚀变作用,还是矿化作用,均受到该作用阶段之前所形成的岩石的化学性质和物理机械性质的控制.岩石物理机械性质中,岩石的孔隙度占有特别重要的地位.无论热液通过何种途径上升,终究是要经过岩石中的孔隙进行化学反应,或直接沉淀在其中.可见岩石中孔隙度的大小及其性质,如孔隙的结构、开放程度、及其形态等,对于热液食变和矿化强弱都起着重要作用. Post-magmatic deposits, regardless of the alteration or mineralization of the surrounding rock, are controlled by the chemical and physical-mechanical properties of the rock formed prior to this stage of action. Rock physics The mechanical properties of the rock occupy a special Important position.No matter hydrothermal solution through which way to rise, after all, is to pass through the pores in the rock chemical reaction, or directly precipitated in it.Visible rock size and the nature of the porosity, such as pore structure, opening degree, And its morphology, etc., for hydrothermal changes and mineralization both play an important role.
其他文献
生产中往往遇到齿条的淬火,而实践告诉我们,每种齿条经淬火后都会产生不同规律的变形。例如图1所示齿条,材料为T10A,要求硬度≥HRC55,变形≤0.25毫米。该齿条淬入160~180℃的
本文报道了存在于中毒死者体液样品中的毒物戊巴比妥钠的分离鉴定方法,其结果由标准谱图和综合分析验证。 This paper reports the isolation and identification of pentob
我厂产品上的窥视孔系腰形法兰孔(图1)。对于这种孔,过去均是采用三次铣削的方法才能完成加工。首先镗铣两端 R40止口尺寸、上圆转盘,用立铣刀铣两端 R 51止口尺寸。接着铣
On August 8, comrades of the CPAFFC were as excited as all the Chinese people on the day of the opening ceremony of the Beijing 2008 Olympic Games. At 5 o’cloc
本文研究了钍萃取工艺过程中微量钍的测定方法。在0.5 N HNO_3介质中,用乙二醇丁醚作互溶剂,该均相溶液用偶氮氯膦-mA作钍的显色剂,进行分光光度法直接测定有机相中微量钍。
我国的职业教育源远流长,历史悠久。本文从我国古代职业教育的建立一直谈到现代高职教育的发展。 Our vocational education has a long history and a long history. This
2007年北京市朝阳区教工委、教委把学校文化建设作为提升全区教育的抓手,提出了加强学校文化建设三年规划的战略目标,将2007至2009年分别确立为校园环境建设年、人文文化建设
1975年我们在鉴定陕西汉中超基性岩岩体矿物时,发现了绿纤石矿物,对其进行了X射线粉晶分析及光性特征鉴定,现作一报导。绿纤石Ca_4(Mg,Fe,Mn)(Al,Fe,Ti),(OH)_2[(Si_3OH)(Si
北安河和密云两重力固体潮台站位于北京地区,在唐山地震震中的西北方向,距震中约160公里。对两台站自1976年1月1日至9月16日的重力固体潮观测资料进行了分析。首先用别尔采夫
国家地质总局1978年在广西柳州召开了水文地质工程地质物探专业会议。 会议的目的是,总结交流建国廿多年来,特别是近几年来,水文物探工作和群众办物探的经验;找出与国内外先