山东阜山金矿东风矿区矿体地质特征及成矿规律研究

来源 :湖南有色金属 | 被引量 : 0次 | 上传用户：yht_816

【摘要】

：

玲珑金矿田阜山金矿东风矿区历史悠久,矿区内构造发育,矿脉众多,矿脉关系错综复杂.通过总结东风矿区的地质条件,分析了矿区207、208、206矿脉地质特征,归纳主要矿体的空间分布、产状、品位变化规律.结合围岩及夹石地质特征,总结了矿体富集的有利部位及分布规律,为矿山找矿勘探提供了地质依据.东风矿区矿体严格受断裂构造控制,断裂构造的拐弯、交汇部位及倾角变化部位赋矿.

【作者】

：

远义飞杜久华马宏伟

【机构】

：

中矿金业股份有限公司,山东招远265400

【出处】

：

湖南有色金属

【发表日期】

：

2021年6期

【关键词】

：

玲珑金矿田东风矿区金矿矿体地质特征成矿规律

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

其他文献

Nonlinear resonance characteristics of a dual-rotor system with a local defect on the inner ring of

In this paper,the nonlinear resonance characteristics of a dual-rotor system are investi-gated with the consideration of a local defect on the inter-shaft bearing of the system.A simplified model of the dual-rotor system is proposed by considering that th

期刊

Combination resonanceDual-rotor systemInter-shaft bearingLocal defectNonline

A high dynamics algorithm based on steepest ascent method for GNSS receiver

High dynamic conditions impose critical challenges on Global Navigation Satellite Sys-tem (GNSS) receivers,leading to large tracking errors or even loss of tracking.Current methods that intend to improve receivers\' adaptability for high dynamics requir

期刊

Carrier tracking loopsFast Fourier Transform(FFT)Global Navigation Satellite S

Dynamic parametric modeling-based model updating strategy of aeroengine casings

For accurate Finite Element (FE) modeling for the structural dynamics of aeroengine casings,Parametric Modeling-based Model Updating Strategy (PM-MUS) is proposed based on efficient FE parametric modeling and model updating techniques regarding uncorrelat

期刊

Aeroengine casingsCorrelated mode pairModel updatingParametric modelingStruc

Improving seeking precision by utilizing ghost imaging in a semi-active quadrant detection seeker

Conventional semi-active laser guidance takes advantage of the laser designator to illu-minate the stable and uniform laser spot on target precisely.The seeker collects the reflected light by a quadrant detector and outputs the relative position informati

期刊

Digital micro-mirror deviceGhost imagingGuidance systemImage acquisitionSemi

Relevant experience learning:A deep reinforcement learning method for UAV autonomous motion planning

Unmanned Aerial Vehicles (UAVs) play a vital role in military warfare.In a variety of battlefield mission scenarios,UAVs are required to safely fly to designated locations without human intervention.Therefore,finding a suitable method to solve the UAV Aut

期刊

Autonomous Motion Planning (AMP)Deep Deterministic Policy Gradient (DDPG)Deep

A mask R-CNN based method for inspecting cable brackets in aircraft

In the aviation industry,cable bracket is one of the most common parts.The traditional assembly state inspection method of cable bracket is to manually compare by viewing 3D models.The purpose of this paper is to address the problem of inefficiency of tra

期刊

Aircraft assemblyAugmented realityCable bracketMask R-CNNSynthetic datasetT

Wetting behavior of AgCu-4.5Ti filler reinforced by carbon nanotubes on C/C composite

The effect of Carbon Nanotubes (CNTs) content on the wettability of AgCu-4.5Ti +x CNTs (wt％) composite filler alloys on C/C composite was investigated.The results show that the added CNTs reacted with element Ti in the filler and produced the dispersed fi

期刊

C/C compositeCarbon Nanotubes (CNTs)Composite fillerMicrostructureWetting

Effects of traverse speed on weld formation,microstructure and mechanical properties of ZK60 Mg allo

ZK60B (Mg-6％ Zn-0.6％ Zr) alloy joints fabricated by bobbin tool friction stir welding(BTFSW) with various traverse speeds were investigated.The sound joint fabricated by the BTFSW was possible under the appropriate welding parameters.The severe plastic de

期刊

Bobbin toolFriction stir welding (FSW)Magnesium alloysMechanical propertiesM

Improvement of machining accuracy in EDCM by enhanced electrochemical reaming based on a non-metalli

Electrochemical Discharge Machining (ECDM) is potentially applicable for the fabrica-tion of film-cooling holes.However,It is extremely difficult for the holes to achieve higher precision and machining quality owing to the working liquid diminish in the l

期刊

Backing layerECDMElectrochemical reamingNon-metallic

Multiaxial fatigue life prediction of composite laminates

A study of composite laminates under tension-torsion biaxial loading is presented.The focus is placed on fatigue lives of composite laminates under different tension-torsion biaxial fati-gue loading paths.A macro-meso model used to predict multiaxial fati

期刊

Composite laminatesFatigue damage parameterLife predictionMultiaxial fatigue

山东阜山金矿东风矿区矿体地质特征及成矿规律研究

与本文相关的学术论文