【摘 要】
:
Soft magnetic Co-based Co-Y-Nb-B bulk metallic glasses (BMGs) without Fe have been developed by micro-alloying Y and Nb into a Co75B25 alloy.First,addition of 3
【机 构】
:
Key Laboratory of Materials Modification by Laser,Ion,and Electron Beams (Ministry of Education),Sch
论文部分内容阅读
Soft magnetic Co-based Co-Y-Nb-B bulk metallic glasses (BMGs) without Fe have been developed by micro-alloying Y and Nb into a Co75B25 alloy.First,addition of 3-4 at.% Y promotes the occurrence of glass transition and increases the supercooled liquid stability and magnetic softness.Co71.5Y3.5B25 metallic glass possesses a large supercooled liquid region(△Tx) of 33 K and low coercivity (Hc) of 1.5 A/m.Subsequent alloying 2-4 at.% Nb into CO71.5Y3.5B25 alloy further enlarges △Tx to 50 K,lowers Hc to 0.9 A/m,and enables the formation of BMGs with a critical sample diameter up to 2.0 mm.The alloying Nb causes the formation of complex (Co,Nb,Y)23B6 competing phase during crystallization and widens the melt undercooling during solidification,which improves the supercooled liquid stability and glass-forming ability,respectively.Co-Y-Nb-B BMGs also exhibit good soft magnetic and mechanical properties,i.e.,low Hc of 0.9-1.2 A/m,relatively high saturation magnetic flux density of 0.36-0.57 T,high yielding strength of 3877-3930 MPa with plastic strain of 0.2%-0.3%,and high Vickers hardness of 1156-1201.The developed soft magnetic Co-based BMGs are promising for applications as structural and functional materials.
其他文献
In cold rolling process,the flatness actuator efficiency is the basis of the flatness control system.The precision of flatness is determined by the setpoints of
介绍了西班牙列车制造商Talgo将云技术应用到列车维修方面的情况。
Considering the dynamic influence of the roll vibration on the lubricant film thickness in the rolling deformation area,nonlinear dynamic rolling forces related
Energy balances are a general fundamental approach for analyzing the heat requirements for metallurgical processes.The formulation of heat balance equations was involved by computing the various components of heat going in and coming out of the oxygen ste
Al0.5Cr0.9FeNi2.5Vx (x =0,0.2,0.4,0.6,0.8,1.0) multi-principal alloys were prepared by vacuum arc melting.The effect of vanadium addition on its microstructure
Using the first-principles methods,the effects of different alloying elements M (M =Fe,Ni,Mn,Si,Mo,Cu,Y) on Cr2O3 with C1 adsorption are studied.The results sho
实际配电网在网络参数、联络开关数量、负荷转供能力等方面与标准算例有着明显区别,为解决实际配电网中联络开关和柔性软开关(Soft Ppen Point,SOP)配合供电问题,采用有源配
The two-pass isothermal hot compression method was used to study the effect of different thermal deformation conditions on static recrystallization behavior in
通过静载荷试验、疲劳试验和线路试验评估了电动车辆转向架构架的疲劳强度。对疲劳试验和线路试验中出现的应力历程的特征进行了评估,采用各种疲劳寿命评估方法对疲劳损伤进行了评估。试验结果表明,在载荷作用下,某些应变片测得的应力和应变按应变片所处的位置呈多轴状态。应根据位置和应力状态确定合适的疲劳评估方法。
昆钢公司积极响应国家号召,深化供给侧结构性改革、加快新旧动能转换、推动企业迈向高质量发展,坚持走延伸产业链、循环经济、科技引领、绿色发展、产城融合的新发展之路,将原有关停后的老旧钢铁生产厂房改造成现代化的钢铁深加工生产基地。在老旧厂房改造中,消防给排水系统设计是需要关注的重点内容。本文以原昆钢第一炼钢厂厂房改造为液压锻造车间为例,对消防给排水系统在改造设计中存在的问题进行分析并提出相应设计方案。