Durning the design process of hydrostatic rotary worktable,the processing and assembly tolerance,(the offset of worktable and the gap of the oil film’s thickness)is ignored.But it will cause that the real bearing of oil pocket deviates from the initial design value,and then the performance of rotary worktable will be reduced significantly.Up to now,no effort is found toward the research of influence of the processing and assembly tolerance on the performance of the rotary worktable.So the hydrostatic oil film is assumed as the elastomer in this paper,and then the bearing capacity of the oil pocket is studied with and without the mass offset of the worktable by taking an expression between the bearing capacity and the oil film’s thickness of the oil pocket as the deform compatibility equation.The influence of the processing tolerance of the oil sealing belt’s gap on the bearing capacity of the oil pocket is analyzed.In the light of the liquid hydrostatic worktable of Gantry Moving Milling Center using on the scene,the oil pocket’s pressure of the worktable is tested using Rotary Worktable Test System under the circumstance of the mass offset of the worktable and the gap tolerance of the oil sealing belt,and then the equivalent offset of worktable,the average pressure of the oil pocket and the actual thickness of the oil film are analyzed respectively.The test results show that the bearing capacity component of the oil pocket caused by G is consistent,and the component caused by M is relative to the position of the oil pocket.When the oil sealing belt’s gap is larger than the theoretical value,the bearing capacity of the oil pocket is smaller than the others;whereas the bearing capacity of the oil pocket is larger than the others.The maximum and minimum equivalent offsets are 0.256 4 mm and 0.047 5 mm,respectively,and the average oil pocket pressure varies from 0.345 MPa to 0.460 MPa,the maximum and minimum value of the actual oil film thickness are 109.976?m(No.7 oil pocket)and 93.467?m(No.10 oil pocket),respectively.The research results can be used to detect the offset of the worktable and the actual thickness of the oil film under processing and assembly tolerance,and provides a basis way for detecting the processing and assembly tolerance of rotary worktable signing reasonably of Gantry Moving Milling Center. Durning the design process of hydrostatic rotary worktable, the processing and assembly tolerance, (the offset of worktable and the gap of the oil film’s thickness) is ignored.But it will cause that the real bearing of oil pocket deviates from the initial design value, and then the performance of rotary worktable will be reduced significantly. Up to now, no effort is found toward the research of influence of the processing and assembly tolerance on the performance of the rotary worktable. So the hydrostatic oil film is assumed as the elastomer in this paper, and then the bearing capacity of the oil pocket is studied with and without the mass offset of the worktable by taking an expression between the bearing capacity and the oil film’s thickness of the oil pocket as the deform compatibility equation. influence the processing tolerance of the oil sealing belt’s gap on the bearing capacity of the oil pocket is analyzed. the light of the liquid hydrostatic worktable of Gantry Moving Milling Center using on the scene, the oil pocket’s pressure of the worktable is tested using Rotary Worktable Test System under the circumstance of the mass offset of the worktable and the gap tolerance of the oil sealing belt, and then the equivalent offset of worktable, the average pressure of the oil pocket and the actual thickness of the oil film are analyzed respectively.The test results show that the bearing capacity component of the oil pocket caused by G is consistent, and the component caused by M is relative to the position of the oil pocket.When the oil sealing belt’s gap is larger than the theoretical value, the bearing capacity of the oil pocket is smaller than the others; but the bearing capacity of the oil pocket is larger than the others. maximum and minimum equivalent offsets are 0.256 4 mm and 0.047 5 mm, respectively, and the average oil pocket pressure varies from 0.345 MPa to 0.460 MPa, the maximum and minimum value of the actual oil film thickness are 109.976? m (No.7 oilpocket) and 93.467? m (No. 10 oil pocket), respectively. The research results can be used to detect the offset of the worktable and the actual thickness of the oil film under processing and assembly tolerance, and provide a basis way for detecting the processing and assembly tolerance of rotary worktable signing reasonably of Gantry Moving Milling Center.