Effects of strain rate on austenite stability and mechanical properties in a 5Mn steel

来源 :钢铁研究学报(英文版) | 被引量 : 0次 | 上传用户:vpvplp
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
The austenite stability and the mechanical properties in a typical medium Mn grade steel,i.e.,5Mn steel,were investigated under a wide range of strain rates through the combination of experimental and theoretical methodologies.The obtained results indicate that austenite is more stable at a high strain rate,which is due to the suppression of the austenite to martensite transformation.This suppression is attributed to the increased stacking fault energy and the high deformation energy barrier.Moreover,the suppression of martensitic transformation also leads to the decrease in the ultimate tensile strength and the uniform elongation.Owing to the increase in an adiabatic heating temperature,an increase in the uniform elongation is acquired at a high strain rate.The obtained fundamental study results shed light on a wide application of the medium Mn steel under different strain rate conditions.
其他文献
The reactions between CO2 gas and liquid Fe-C alloy with different initial carbon concentrations at 1873 K were investigated using experimental results,thermodynamic equilibrium,and kinetic analysis.The average CO2 conversion is greater than 80%when the c
The sliding wear property of high-carbon nanostructured bainitic bearing steel with the equal initial hardness and different microstructures was investigated,and the reasons for the difference of wear resistance between the cementite-bearing(CB)and cement
采用高通量场发射扫描电镜结合图像批处理技术以及全自动显微维氏硬度分析技术对2种不同成分(W1和W2)的火车车轮轮辋踏面附近较大范围内的显微组织和硬度进行了原位统计分布表征,探究了轮辋靠近踏面的关键区域铁素体面积分数和珠光体片层间距的分布规律.通过大尺度原位统计分布表征结果可以发现,2种车轮铁素体面积分数自踏面往里均呈现逐渐增加的趋势,但固溶强化元素Si和沉淀强化元素V的含量差异以及W2车轮所采用更为精细的阶梯式淬火工艺对车轮的微观组织和硬度的定量分布有较大影响.固溶强化和沉淀强化元素含量较少的W1车轮的铁
Iron ore containing BaSO4 may have a senes of effects on the quality of the sinter and performance of the blast furnace.Thus,the effect mechanism of BaSO4(0-6.0 mass%)on the compressive strength,mineral composition,and microstructure of the sinter was inv
Effect of titanium microalloying on the microstructure and mechanical properties of vanadium microalloyed steels for hot forging was studied.Titanium microalloying improves the mechanical properties mainly through refining the austenite grains.When the he
The effects of Si content,graphite volume fraction and pearlite volume fraction on the thermal conductivity of ductile iron were studied based on theoretical model analysis.Calculated results showed that the thermal conductivity of ductile iron was more s
高炉炼铁过程通过增煤减焦实现节能减排目标,针对人工操作模式存在主观性、粗糙性和滞后性难以实现增煤减焦的问题,采用上下协同优化控制方法,一方面通过上部提前匹配减焦方式维持高温区热平衡,另一方面通过富氧鼓风保证下部喷入煤粉的高消化率,使煤粉在风口回旋区充分燃烧.进而从控制角度解析描述增煤减焦过程,将铁水温度的稳定控制问题转换为风口回旋区温度的稳定控制问题,提出增煤减焦协同优化控制策略及风口回旋区温度对焦炭和煤粉不同滞后时间的稳定控制策略.首先,建立煤粉燃烧系统的T-S模糊模型,将辨识得到的喷煤最大时延区间进行
利用离散单元法研究烧结矿竖冷炉在排料过程中颗粒运动的流型和速度分布.模拟结果表明,烧结矿颗粒在下移过程中,运动流型依次呈“一”→“S”→“V”转变;在竖冷炉腔内的大部分区域,烧结矿颗粒保持整体流动;在中心风帽上方的局部区域(宽480 mm,高1280 mm),运动流型会随排料的进行在整体流和漏斗流之间转变.烧结矿颗粒速度分布表明,在中心风帽上方会形成更大区域的(宽960 mm,高3200~3840 mm)梯形缓慢流动区.缓慢流动区内颗粒下移速度较小,冷却后的颗粒不能及时排出炉外,不利于气固换热效率的提高.
Influence of coiling temperature(CT)on the microstructure and mechanical properties of a hot-rolled high-strength steel microalloyed with Ti,Mo and V was elucidated.The precipitation behavior of nano-sized particles was investigated by theoretical calcula
通过数值模拟方法,研究了210 t铁水包静置温降过程中铁水包包盖和铁水液位对铁水温降速率的影响.模型中使用S2 S辐射传热模型来考虑渣层与包盖间的辐射传热,并分析了不考虑铁水自然对流对计算结果的影响.结果表明:铁水静置过程计算中,考虑铁水自然对流现象能够明显提高铁水温度的均匀性,并提升计算结果的准确性.使用包盖能够有效减少铁水包静置过程铁水的热量散失,提高铁水的4 h静置后最终温度13℃.铁水包内铁水液位会影响静置过程中铁水温降速率,液位降低会增加铁水温降速度.