【摘 要】
：
A novel semisolid micro fused-casting (MFC) for preparing A356 alloy strips is proposed, and the effects of process parameters of pouring temperature on the microstructure and properties of A356 alloy strips are investigated. MFC means that the semisolid
【机 构】
：
Henan Key Laboratory of Research for Central Plains Ancient Ceramics, Pingdingshan University, Pingd
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
A novel semisolid micro fused-casting (MFC) for preparing A356 alloy strips is proposed, and the effects of process parameters of pouring temperature on the microstructure and properties of A356 alloy strips are investigated. MFC means that the semisolid metal slurry was pressed out from the outlet of bottom of crucible to the movable plate, and directly solidified and formed layer by layer. The microstructure and properties of A356 semisolid alloy slurry were influenced by the cooling conditions. Results show that the aluminu alloy A356 strip samples fabricated by micro fused-casting had good performances and uniform structures with the pouring temperature at 595 ℃ and the substrate movement speed at 18 mm/s. The fine grains of the primary α-Al phase with average grain size of 53 μm and shape factor up to 0.72 was obtained, the ultimate tensile strength of the aluminum alloy A356 strip reaches 243.79±3.91 MPa, while the average vickers hardness is 82.65±1.86 HV.
其他文献
The La-Mg-Ni-Mn-based AB2-type La1-xCexMgNi3.5Mn0.5 (x = 0, 0.1, 0.2, 0.3, and 0.4) alloys were fabricated by melt spinning technology. The effects of Ce content on the structures and electrochemical hydrogen storage performances of the alloys were studie
Three different kinds of coatings were coated on the concrete surface, and the changes in appearance, surface roughness, microstructure and components of coatings in artificial sewage were investigated. In addition, the strength, micrograph, mineral compo
Polytetrafluoroethylene (PTFE) is a commonly used seal material for oil-free engine that is well known for its excellent tribological properties. In this work, the nano-ZrO2 particles were used as the friction modifiers to improve the friction and wear pe
Sapphire,belonging to hexagonal crystal system,is typically anisotropic which makes it direction-sensitive.To research the effects of growth directions on properties of sapphire,c-[0001]seed(c-sapphire)and a-[11-20]seed(a-sapphire)were used to prepare sap
Silicon nitride ceramics were prepared by means of a hot-press sintering method. The ablation behavior was studied by plasma wind tunnel tests. The data suggested that, under low heat flux and stagnation pressure conditions, the ablation process was contr
A three-dimensional dynamic model for nano/micro-fabrications of silicon was presented.With the developed model, the fabrication process of silicon on nothing (SON) structure was quantitatively investigated. We employ a diffuse interface model that incorp
ZrB2-SiC based ultra-high temperature ceramic (UHTC) struts were firstly proposed and fabricated with the potential application in the combustor of scramjets for fuel injection and flame-holding for their machinability and excellent oxidation/ablation res
Calcium sulfate whisker (CaSO4 whiskers), a new type of microfiber material, was used in cement matrix to increase the strength of the cement based composites. Effect of CaSO4 whiskers on the mechanical properties of the resulting cement mortar was also s
A micro-scale finite element method (FEM) was proposed to precisely calculate the heat conduction between mortar and aggregate, and thus to accurately predict the non-uniformity of concrete pouring temperature. The concrete temperature field during vibrat
Triisopropanolamine (TIPA) was used as an early strength component to study its effects on mortar strength, cement paste setting time and early hydration characteristic of cement. And the early strength mechanism of TIPA at low temperature of 5 ℃ was also