• 不 限
  • 期刊论文
  • 硕博论文
  • 会议论文
  • 报 纸
  • 英文论文
  2. 您的位置
  3. 首页
  4. 会议论文
  5. Assessment of deformation behavior in aluminum alloy with diffraction-amalgamated grain-boundary tra

Assessment of deformation behavior in aluminum alloy with diffraction-amalgamated grain-boundary tra

来源 :15th International Conference on Aluminium Alloys(ICAA15)(第十 | 被引量 : 0次 | 上传用户：RIPV2
【摘 要】
：
The behavior of individual grain during plastic deformation is affected by shape and size of grains and the crystal orientations for the grains in polycrystalline.We proposed new diffraction-amalgamat
【作 者】
：
Kyosuke Hirayama Hiroyuki Toda Yukako Teraoka Kentaro Uesugi Akihisa Takeuchi 
【机 构】
：
Department of Mechanical Engineering, Kyushu University, Japan
【出 处】
：
15th International Conference on Aluminium Alloys(ICAA15)(第十
【发表日期】
：
2016年3期
下载到本地 , 更方便阅读
下载此文 赞助VIP
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
The behavior of individual grain during plastic deformation is affected by shape and size of grains and the crystal orientations for the grains in polycrystalline.We proposed new diffraction-amalgamated grain-boundary tracking (DAGT) technique, which was developed by combining the grain boundary tracking (GBT) technique and a pencil beam XRD.
其他文献
浅谈滕州某酒店空调设计与节能
根据酒店项目的地域特点、建筑功能及业主提出的要求,对滕州某酒店项目空调冷、热源系统采用常规电动压缩式制冷、溴化锂吸收式制冷(供热)、市政热水供热及燃气热水锅炉供热的可行性进行分析与比较,并提出合理的方案论证及建议.
会议
酒店空调系统节能设计
Hybrid nanostructured aluminum alloy with high strength
Strengthening aluminum alloys is a longstanding task since the discovery of the age-hardening phenomenon in 1906.The upper strength limit of bulk Al alloys is ～0.7 GPa by conventional precipitation st
会议
Microstructure-based analysis of fretting fatigue behaviour of Al-Zn-Mg alloy
The effects of microstructural characteristics on the fretting fatigue behavior in Al-Zn-Mg alloy were systematically investigated.The dislocation substructures of Al-Zn-Mg alloy under different stres
会议
Microstructure optimization for damage evolution in ductile deformation by R4ME methodology
A new technology for materials development,Reverse 4D Materials Engineering(hereinafter R4ME), is achieved through the utilization of 3D/4D imaging technique and image-based simulation.R4ME is a rever
会议
Effect of homogenization and annealing treatment on mechanical properties and corrosion resistance o
For weldable structures of aerospace application non-heat treatable Al-Mg alloys are widely used.Improvement of mechanical properties of these alloys is possible with an additive of small amount of sc
会议
Materials selection and mechanical testing of the aluminum alloy drill pipe for oil and gas industry
Aluminum alloy drill pipe has been widely used as the effective tools to solve drilling problem for oil and gas Industry due to its high-strength and low density.The materials selection and mechanical
会议
Effect of dispersoids on long term stabile electrical aluminium connections
In electrical power systems pre-stressed screw connections of conducting paths/bus-bars out of Al alloys are common, whereby the operating temperature shall be increased up to 140 ℃ in the future.At t
会议
Low-temperature creep mechanism in ultrafine-grained aluminum at extremely low stress range
Low temperature creep behavior around room temperature was examined for coarse-grained (CG) and ultrafine-grained (UFG) aluminum.The materials were fabricated through accumulative roll bonding and sub
会议
Effect of solute elements on strengthening and work hardening of aluminium alloys at various tempera
This work is an experimental study on solid solution strengthening of aluminium alloys.Flow behaviour of high-purity Al-Mg and Al-Si binary alloys is characterised and compared to that of a base mater
会议
The solid solution hardening of Mg in Al-Mn-Cu brazing sheet alloys at the room and elevated tempera
Al-1.5％Mn-0.5％Cu alloys with increasing Mg content from 0.1, 0.5, 1.0, 1.5 to 2.0wt.％have been developed for automotive heat exchanger units.They were DC cast and processed down to a final gauge of 1m
会议