论文部分内容阅读
对铬盐生产厂和铬铁合金厂在生产过程中排放的固体废渣-铬渣,进行原材料性能分析,通过对其与土或石灰进行混合,研究不同掺配比例下的混合料性能,以判定其是否可以作为路基填料使用,解决铬渣处理物的出路问题.研究表明,通过掺配一定比例的土和石灰,铬渣可以作为路基的填筑材料.
铬渣无害化处理物力学性能研究
【摘 要】
：
对铬盐生产厂和铬铁合金厂在生产过程中排放的固体废渣-铬渣,进行原材料性能分析,通过对其与土或石灰进行混合,研究不同掺配比例下的混合料性能,以判定其是否可以作为路基填料使用,解决铬渣处理物的出路问题.研究表明,通过掺配一定比例的土和石灰,铬渣可以作为路基的填筑材料.
【机 构】
：
天津市市政工程研究院
【出 处】
：
第七届中国公路科技创新高层论坛
【发表日期】
：
2015年8期
其他文献
Research and Application on Platform Independent Automobile Remote Diagnosis Technology Based on Mob
In this paper,from the new requirements of mobile Internet environment for remote diagnosis system of automobile proposed starting,the development mode and costs of the traditional remote system and p
Thermal runaway(TR)propagation within a large format lithium ion battery module includes two stages:the Initiation Stage and the Propagation Stage.Experiments were conducted to investigate the mechani
Development and Application of Intelligent Diesel Idling Start/Stop Technology for Commercial Vehicl
The first intelligent diesel idling start/stop technology for commercial vehicles in China was developed by FAWDE.realizing the logic development of intelligent diesel idling start/stop technology,24
Recently weight reduction is increasingly needed in automotive industry to reduce energy consumption and air pollution.In this paper,development of composite material rear bumper beam(GMT,LFT-D,PC-PBT
This is an off-road vehicle independently developed with spare tire mounted on the tail door which can meet military and civilian requirements.In 18000km reliability test,the system problem that tail
A rectilinear rear independent suspension(RRIS)which has the ability to remain the wheel alignment parameters(WAPs)invariable in theory is presented in this paper.The kinematic analysis of the RRIS in
Aimed at safety of vehicle collision avoidance at high speed,a coupled driving/breaking and steering control method is proposed.Based on the differential flatness theory,the flatness-based controller
在某重型商用车驾驶室开发过程中,以驾驶室的钣金件厚度为变量进行正交数组试验,采用响应面法建立此驾驶室的近似模型,然后使用ASA优化方法,以驾驶室的弯曲刚度、扭转刚度和1阶弯曲模态为性能约束,驾驶室总质量为目标,进行多目标优化,最终,得到轻量化设计结果,误差为1.4％-4.9％,在可接受范围内.采用这种多目标的轻量化设计方法,使此款重型商用车驾驶室降重为30kg(降幅6.9％),降重效果显著.这种系
本论文介绍了电装新开发的车辆蓄冷空调系统，详细说明了该产品的设计理念及其节油效果。首先利用蓄冷蒸发器特性，通过计算其热容量验证蓄冷材的作用效果。传统蒸发器在压缩机停止运转后，吹出口温度急剧上升，19s后就达到了舒适性界限-15℃。采用蓄冷蒸发器，其吹出口温度一旦超过10℃，蓄冷材就会抑制温度上升，达到15℃时所需时间延长至54s。据台架测试和实际车辆测试结果，怠速起停时的舒适度得到了明显改善。根据