【摘 要】
:
A new type of explosive ink formulation that can be quickly cured was prepared with unsaturated polyester as binder,styrene as active monomer,2,4,6-trimethylbenzoyl-diphenylphosphine oxide as photoinitiator,and hexanitrohexaazaisowurtzitane (CL-20) as the
【机 构】
:
School of Environment and Safety Engineering,North University of China Taiyuan Shanxi,030051,PR Chin
论文部分内容阅读
A new type of explosive ink formulation that can be quickly cured was prepared with unsaturated polyester as binder,styrene as active monomer,2,4,6-trimethylbenzoyl-diphenylphosphine oxide as photoinitiator,and hexanitrohexaazaisowurtzitane (CL-20) as the main explosive.Then the explosive ink direct writing technology was used to charge the micro-sized energetic devices,the curing mechanism of the explosive ink was discussed,and the microstructure,safety performance and explosive transfer performance of the explosive ink molded samples were tested and analyzed.Results indicate that the composite material has a fast curing molding speed,its hardness can reach 2H within 8 min.The crystal form of CL-20 in the molded sample is still ε type.The CL-20 based W-curing explosive ink formulation has good compatibility,its apparent activation energy is increased by about 3.5 kJ/mol.The composite presents a significant reduction in impact sensitivity and its characteristic drop height can reach 39.8 cm,which is about 3 times higher than the raw material.When the line width of charge is 1.0 mm,the critical thickness of the explosion can reach 0.015 mm,and the explosion velocity is 7129 m/s when the charge density is 1.612 g/cm3.
其他文献
This paper studies the shaped charge jet performance in terms of different liner shapes including conical,bell,hemispherical and bi-conical liners.The critical angles and the relevant flow velocities for the zir-conium liner material were calculated analy
Thermal safety of modular charge which is fed into and retained in the chamber after gun fires consecutively is first investigated with cook-off method.A two-dimensional cook-off model of modular charge in gun chamber is established and the cook-off proce
One of the main challenges for multi-wheel hub motor driven vehicles is the coordination of individual drivetrains to improve mobility and stability in the steering process.This paper proposes a dual-steering mode based on direct yaw moment control for en
3-nitro-1,2,4-triazol-5-one (NTO) is the main component of insensitive munitions (IM) formulation because of its outstanding insensitive properties.In this paper,a series of NTO/HMX-based composite explosives were prepared and characterized.The study focu
This paper considers the time difference of arrival (TDOA) and frequency difference of arrival (FDOA)estimation problem for joint localization using unmanned aerial vehicles (UAVs),involving range migration (RM) and Doppler ambiguity within observation in
The effects of magnesium/polytetrafluoroethylene (Mg/PTFE) pyrotechnic compositions on the coupled flow field and reignition mechanism are important aspects governing the performance and range of base bleed projectiles (BBPs).Owing to a decrease in pressu
Microsatellites have been widely applied in the fields of communication,remote sensing,navigation and science exploration due to its characteristics of low cost,flexible launch mode and short development period.However,conventional solid-propellant have d
Because of the complexities of tire-road interaction,the wheels of a multi-wheel distributed electric drive vehicle can easily slip under certain working conditions.As wheel slip affects the dynamic per-formance and stability of the vehicle,it is crucial
In this study,we investigated electric explosion of iron wire in distilled water with different energy input adjusted by charging voltage.The as-prepared samples were characterized by X-ray diffraction (XRD),scanning electron microscopy (SEM),transmission
All underwater drilling and blasting operations generate seismic waves.However,due to a lack of suitable vibration sensing instruments,most studies on the propagation of seismic waves have been limited to shorelines near construction areas or wharfs,where