【摘 要】
：
With the risk of disappearing for the rock paintings considering long-term exposure in Helan Mountain, the freeze-thaw(F-T) cycling experiments were carried out with 12-hour F-T cycling (0, 10, 20, 30, and 40 F-T cycles) under five kinds of confining pres
【机 构】
：
School of Physics and Electronic and Electrical Engineering, Ningxia University, Yinchuan 750021, Ch
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
With the risk of disappearing for the rock paintings considering long-term exposure in Helan Mountain, the freeze-thaw(F-T) cycling experiments were carried out with 12-hour F-T cycling (0, 10, 20, 30, and 40 F-T cycles) under five kinds of confining pressures(5, 10, 20, 30, and 40 MPa). The acoustic emission (AE)detect technology was used to reveal the rock fracturing characteristics during the triaxial compression test whole process. The stress-strain relation changes along with different confining pressures and F-T cycles. Peak stress and residual stress changes along with different confining pressures and damages, and the variation of axial stress-AE ringing counts-time changes along with different confining pressures and F-T cycles. The damage variable with AE parameter under F-T and force coupling was defined for the first time, and the damages model was established. The experimental results show that the F-T cycles lead to the decrease of rock strength and the gradual transformation of compression failure mode from brittleness to plasticity. The confining pressure provides a certain ability to resist deformation and inhibit crack growth for rock samples after F-T cycles. The temporal and spatial evolution law of AE counts well corresponds to the loading and failure process of the rock samples. The AE 3D positioning technology can accurately capture the development position and direction of internal cracks and pores of rock, and the failure form is conical shear failure. The established damage model has a better fittingness between the theoretical calculation results and the test results, and is reasonable to be used in the future for protection of Helan Mountain rock painting.
其他文献
Al2O3 particles reinforced hypereutectic Al-Si composites were prepared by in situ Fe2O3/Al reaction system. The thermodynamic analysis and microstructure evolution were investigated by differential scanning calorimetry, optical microscope, scanning elect
A new strategy to fabricate oxygen-promoted Cu,N co-doped carbon (OP-CuN@C) composites is reported. The strategy consists of only two simple steps: chemical polymerization and high temperature carbonization. Electrochemical measurements were conducted to
The heavyweight ultra-high performance concrete (HUHPC) was prepared with barite sand partially replaced by titanium-rich heavy slag sand (THS) at replacement proportion of 0％, 30％, 50％, 70％ and 100％ in this work. The results show that THS incorporation c
The pre-soaked shale employed as an internal curing agent and CaO employed as expansion agent were incorporated into concrete to investigate their effects on the mechanical properties and autogenous deformation of early-age concrete. We have conducted the
The physical performance of recycled asphalt was used as the main evaluation index to study the optimal range of a self-made rejuvenator. Through the penetration, viscosity and gel permeation chromatography (GPC) tests, the diffusion degree of the rejuven
The electrical conductivity of graphene/cement composite before and after carbonation was tested by a four-electrode method. The General Effective Media equation was adopted to fit the experiment results. EIS (electrochemical impedance spectroscopy) was e
A polarizing microscope, X-ray diffraction (XRD), fourier transform infrared spectrometer (FTIR), scanning electron microscope and energy dispersive spectrometer (SEM-EDS), X-ray photoelectron spectroscopy (XPS), and micro computed tomography (Micro CT) w
Nano-pellet α-Al2O3 was prepared using aluminum nitrate as precursor and urea as fuel by a fast method of solution combustion synthesis. The formation of the nano material was dependent on the molar ratio of fuel/oxidant, calcination temperature, and fore
Aluminum sol, dry gel, and film were prepared by sol-gel and a dipping-withdrawing method. The effect of polyethylene glycol (PEG) on the behavior of aluminum sol, gel, and film was investigated by DLS, rotary viscometer, XRD, IR, EPMA, and light microsco
A quantitative pH measuring method has been used to measure the pH of pure and blended cement mortars. The blended cement mortars incorporating supplementary cementitious materials (SCMs) such as fly ash (FA), ground granulated ballast furnace slag (GGBFS