【摘 要】
：
Generalized parallel mechanisms with a configurable moving platform have become popular in the research field of parallel mechanism.This type of gripper mechanism can be applied to grasp large or heavy objects in different environments that are dangerous
【机 构】
：
Department of Mechanical Engineering,Beijing Jiaotong University,Beijing 100044,China
论文部分内容阅读
Generalized parallel mechanisms with a configurable moving platform have become popular in the research field of parallel mechanism.This type of gripper mechanism can be applied to grasp large or heavy objects in different environments that are dangerous and complex for humans.This study proposes a family of novel (5 + 1)degrees of freedom (three translations and two rotations plus an additional grasping motion) gripper mechanisms based on the generalized parallel mechanisms with a configurable moving platform.First,the configurable moving platform,which is a closed loop,is designed for grasping manipulation.The hybrid topological arrange-ment is determined to improve the stiffness of the manipulator and realize high load-to-weight ratios.A sufficient rule based on Lie group theory is proposed to synthesize the mechanism.The hybrid limb structure is also enumerated.A family of novel gripper mechanisms can be assembled through the hybrid limbs by satisfying the rule.Two examples of the gripper mechanisms with and without parallelogram pairs are shown in this study.A kinematic analysis of the example mechanism is presented.The workspace shows that the mechanism possesses high rotational capability.In addition,a stiffness analysis is performed.
其他文献
采用失重法、电化学法及表面分析测试研究了农林废弃物核桃青皮提取物(WGHE)与阴离子表面活性剂十二烷基磺酸钠(SLS)对冷轧钢在2.0 mol/L H3PO4介质中的缓蚀协同效应,并对WGHE中的缓蚀有效成分进行了探究.结果 表明:单独的WGHE、SLS具有中等程度的缓蚀性能,50℃时100 mg/L的缓蚀率仅为50％左右;WGHE/SLS复配后缓蚀率不断上升,最高缓蚀率可达95.3％,两者之间存在显著的缓蚀协同效应,缓蚀协同效应系数随温度的升高而增大.WGHE/SLS复配缓蚀剂更能同时有效抑制阴极和阳极
This paper proposes a new Deep Feed-forward Neural Network (DFNN) approach for damage detection in functionally graded carbon nanotube-reinforced composite (FG-CNTRC) plates.In the proposed approach,the DFNN model is developed based on a data set containi
In waterfront geotechnical engineering,seismic and drainage conditions must be considered in the design of retaining structures.This paper proposes a general analytical method to evaluate the seismic active earth pressure on a retaining wall with backfill
探究了CO2湿气环境中P110SS抗硫钢在不同温湿度下的S腐蚀特征及腐蚀机理.采用X射线光电子能谱(XPS)和扫描电子显微镜(SEM),对P110SS钢表面腐蚀产物膜的化学组成、微观形貌及厚度及去除腐蚀产物后基体的微观形貌进行了表征.结果 表明:在60℃、相对湿度为30％的条件下,S不会参与腐蚀反应,但腐蚀环境中的Cl和CO2会导致抗硫钢发生局部腐蚀;当相对湿度升高至60％和90％时,S参与了腐蚀的阴极反应,生成FeS,并导致抗硫钢发生全面腐蚀.在80℃、相对湿度为30％的条件下,S也参与腐蚀的阴极反应,
The demand for redundant hydraulic manipulators that can implement complex heavy-duty tasks in unstructured areas is increasing;however,current manipulator layouts that remarkably differ from human arms make intuitive kinematic operation challenging to ac
Robot-assisted technology has been increasingly employed in the therapy of post stroke patients to deliver high-quality treatment and alleviate therapists\' burden.This paper introduces a novel parallel end traction apparatus (PETA) to supplement equipm
分别测试了新型F级船用低温钢板表面生成不同氧化物后的往复摩擦行为,并结合白光干涉仪以及扫描电子显微镜分别对钢样的显微组织形貌和磨痕形貌进行了表征.结果 表明:γ-FeOOH氧化层钢样、原始钢样、Fe3O4氧化层钢样的耐磨蚀性能依次变高.其中,致密完整的Fe3O4氧化层钢样的磨损量最低,磨痕轮廓深度和尺寸都最小,表面以粘着磨蚀为主,耐蚀性也最好;γ-FeOOH氧化层微观结构较为疏松,摩擦系数最小,但是在摩擦腐蚀的协同作用下磨损量最大,磨损机理皆以磨粒磨损为主;未处理钢样的耐磨蚀性能处于两种预氧化钢样之间,以
The safety of human-robot interaction is an essential requirement for designing collaborative robotics.Thus,this paper aims to design a novel variable stiffness actuator (VSA) that can provide safer physical human-robot interaction for collaborative robot
Transfemoral amputees (TAs) have difficulty in mobility during walking,such as restricted movement of lower extremity and body instability,yet few transfemoral prostheses have explored human-like multiple motion characteristics by simple structures to fit
采用钛酸酯改性硅烷偶联剂作为封孔剂,利用浸渍提拉法对5056铝箔阳极氧化膜进行封孔处理,研究了偶联剂溶质配比、浸渍时间、烘干时间和温度对铝箔耐蚀性能的影响,并探讨了钛酸酯对涂层耐蚀性提升的机理.结果 表明,经钛酸酯改性硅烷偶联剂封孔后,阳极氧化膜层表面形成了连续致密的复合膜,膜层厚度在铝箔双表面均匀一致;当溶质中Ti∶Si=0.3∶5.7时,复合涂层耐蚀性最优;其重铬酸钾耐蚀点滴时间在19 ℃持续30 min,自腐蚀电流密度低至7.42 nA/cm2,盐雾实验16d表面出现腐蚀斑点,远高于单一硅烷涂层对应