论文部分内容阅读
YAG:Nd3 激光棒在调Q应用时的限制
【出 处】
：
中国激光
【发表日期】
：
1977年4期
其他文献
通过在CsPbBr3纳米晶体中加入油胺铟(In(OAm)3)和支化三(二乙胺)膦(TDP)配体,在减缓晶体生长速度的同时促进取向生长,获得了CsPbBr3钙钛矿纳米棒材料。通过透射电子显微镜、X射线衍射系统、紫外-可见分光光度计、光致发光光谱仪对所制备的CsPbBr3钙钛矿纳米棒晶体特性进行表征,结果表明该纳米棒具有质量好、缺陷密度低、发光性能较好的优点;利用可变条纹长度和变功率PL光谱测得了样品的增益系数(860 cm -1)和阈值功率(17.5 μJ/cm 2);同时测量了样品在极端老化的双八五(温度
提出了一种电压温度双参量光纤传感器.在理论上分析了从一个敏感晶体上分离出温度、电压两种信息的可能性:石英晶体作为敏感元件.通过合理安排传感头中各部件.传感器同时输出两路信号:一路是包含Pockels效应的电压信号;一路是石英晶体旋光效应的信号.由于旋光效应与温度有关.这路信号用来反映传感头光路上的温度信息.实验获得理论所预期的结果.从而只使用一个传感头就可以同时测量电压与温度.给出了实验装置.结果
距离测量作为几何量测量关键共性基础技术之一,在科学研究、高端装备制造及空间探测等领域有重要应用。新兴的双光梳绝对测距技术充分发挥了光学频率梳的时域超短脉冲和频域高分辨特性,能实现大范围、高精度、高测速的绝对距离测量。首先,在简要阐述双光梳基本原理的基础上,着重介绍了双光梳飞行时间法测距和相位法测距的研究进展;然后,介绍了双光梳测距技术的功能拓展、仪器化进程及应用实例;最后,对双光梳测距的发展进行了展望。
The ultrafast fiber laser has attracted a great deal of research interest due to its low cost, high efficiency, and simple maintenance. Optical passive devices are vital parts of a fiber laser. In order to obtain a fiber laser with high quality, optical p
期刊
基于腔量子电动力学（QED），通过双光子过程，提出了一种制备三粒子singlet态的简单方案。一个最初处于激发态的
Optical beam steering by using tunable, narrow-linewidth butt-coupled hybrid lasers in a silicon nit
Chip-scale, tunable narrow-linewidth hybrid integrated diode lasers based on quantum-dot RSOAs at 1.3 μm are demonstrated through butt-coupling to a silicon nitride photonic integrated circuit. The hybrid laser linewidth is around 85 kHz, and the tuning r
期刊
The direct replication of W/Si supermirrors is investigated systematically. W/Si supermirrors are fabricated by direct current (DC) magnetron sputtering technology. After deposition, the supermirrors are replicated from the supersmooth mandrels onto ordin
Mode distortion induced by stimulated Raman scattering (SRS) has become a new obstacle for the further development of high-power fiber lasers with high beam quality. Here, an approach for effective suppression of the SRS-induced mode distortion in high-po
We propose a continuous-wave (CW) middle infrared (MIR) and long infrared (LIR) dual-band laser for the calibration and effect research of infrared detecting and imaging systems. A total output power of 18 W is achieved by the proposed dual-band laser thr
A non-scanning, non-interferometric, three-dimensional (3D) optical profilometer based on geometric optics, critical angle principle, and the use of a charge-coupled device (CCD) camera is presented. The surface profile of the test specimen can be transfe