Controlled Synthesis of Core-Shell Nickel Microspheres with Solid Core and Porous Shell by Precipita

来源 :武汉理工大学学报(材料科学版)(英文版) | 被引量 : 0次 | 上传用户:lubin_1985
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Nickel oxalate micro-spheres with core-shell structure of solid core and radiate shell were synthesized by precipitation method in a mixed water solution,with oxalic acid and nickel acetate as raw materials,through dropping ammonium hydroxide to adjust the solution pH value to about 8.0.Nickel microspheres with core-shell structure of solid core and porous shell were prepared by decomposing of nickel oxalate microspheres precursor at about 340 ℃ in argon atmosphere.The analyses of infrared spectroscopy (IR) indicates that the composition of the powders is nickel oxalate.The analyses of atomic absorption spectrometry (AAS) and organic elemental analysis (OEA) indicate that the molar ratio of (C2O4)2-/Ni2+ is about 1.02,close to the theoretical value of 1.0.The results of the thermo-gravimetric and differential thermal gravity analyses (TG-DTG) indicate that the molar ratio of (C2O4)2-/Ni2+ is about 1.06,also close to the theoretical value of 1.0.The analysis of X-ray diffraction (XRD) indicates that the composition of black powders as-prepared is nickel,which has a face-centered cubic crystal structure with average crystal grain size about 16.87 nm.The images of scanning electron microscopy (SEM) indicate that the morphology of nickel oxalate microspheres is a coreshell structure with solid core and radiate shell.The diameter of nickel oxalate microspheres is about 3 μm,and the shell consists of a large number of thin nanorods.The images of SEM also indicate that the morphology of nickel microspheres is a core-shell structure with solid core and porous shell.The diameter of nickel microspheres is about 2 μm,and the shell consists of a large number of nickel grains,surface holes and through holes.The diameter of nickel grains is about 50-100 nm,and the diameter of holes is about 50-200 nm.
其他文献
The nucleation process of graphene films prepared by pulsed laser deposition has been investigated in detail. It is found that graphene nucleates at the steps on the substrate surface firstly, from aggregation of nuclei into particles. High pulsed laser e
In order to explore the effect of high-temperature annealing on the mechanical performances and microstructures of different oxygen SiC fibers, two types of silicon carbide (SiC) -based fibers, specified as XD-SiC fibers (low oxygen) and Nicalon-201 fiber
A recrystallization and partial melting (RAP) process was introduced to prepare the semi-solid 7075 aluminum alloy used for thixoforming. In order to obtain an ideal semi-solid microstructure, a series of extrusion experiments were conducted to comparativ
A plasma cladding experiment was carried out to investigate the characteristics(surface hardness, microstructure, friction, wear properties from different substrates to the cladding layer and the bond strength) of plasma cladding Fe-Cr-Nb-Si-Mo alloy clad
The 0.6mol% CuO-doping 0.996(0.95Na0.5K0.5NbO3-0.05LiSbO3)-0.004FeBiO3 (KNN-LSBF-CuO) piezoelectric ceramics were synthesized by a solid-state reaction technique, and the structure and piezoelectric properties dependence of sintering time in KNN-LS-BF-CuO
Low-cost porous calcined dolomite microspheres were prepared by simple spray drying and subsequent calcination. Effects of calcination temperature on phase evolution and adsorption properties of MB were investigated systematically. Results showed that mic
Polystyrene crosslinked microspheres were prepared by soap-free emulsion polymerization using styrene (St) and divinylbenzene (DVB) as monomers; then, the microporous structure was knitted by the Friedel-Crafts alkylation reaction, and the Au nanoparticle
The CdS/ spherical g-C3N4 n-n heterojunction photocatalyst was fabricated via a solvothermal method. The tetracycline was used to characterize the photocatalytic properties of the as-developed hybrids. The photocatalytic degradation mechanism of the as-de
Chemically functionalized carbon nanotubes were combined with PVC to enhance both toughness and strength by simply mixing long alkyl chain modified multi-wall carbon nanotubes (abbreviated as MWNTs) or Ester-functionalized soluble MWNTs (abbreviated as eM
The preparation of SiBNC ceramic oxidation-resistant coating on carbon fiber via precursorsolution infiltration and pyrolysis (PIP) method was presented and discussed in detail. Moreover, the microstructures and the components of the coating were characte