【摘 要】
：
Three-dimensional distribution of solute elements in an Mg-Zn--Gd alloy during ageing process is quantitatively characterized by three-dimensional atom probe (3DAP) tomography.Based on the radius distribution function,it is found that Zn-Gd solute pairs i
【机 构】
：
School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 1
论文部分内容阅读
Three-dimensional distribution of solute elements in an Mg-Zn--Gd alloy during ageing process is quantitatively characterized by three-dimensional atom probe (3DAP) tomography.Based on the radius distribution function,it is found that Zn-Gd solute pairs in Mg matrix appear mainly at two peaks at early stage of ageing,and the separation distance between Zn and Gd atoms could be well rationalized by the first-principle calculation.Moreover,the fraction of Zn-Gd solute pairs increases first and then decreases due to the precipitation of long-period stacking ordered (LPSO) structures.Both the composition of the structural unit in LPSO structure and the solute enrichment around it are quantified.It is found that Zn and Gd elements are synchronized in the LPSO structure,and solute segregation of pure Zn or Gd is not observed at the transformation front of the LPSO structure in this alloy.In addition,the crystallography of transformation front is further determined by 3DAP data.
其他文献
The microstructure,mechanical properties and corrosion behavior of Mg-2Zn-0.6Zr alloy under the as-cast and asextruded conditions were investigated.Microstructure analysis indicated the remarkable grain refinement by extrusion,as well as notable reduction
Machining,especially dry machining of titanium alloys,has been one of the most significant challenges for carbide cutting tools.In this study,aluminum-rich AlTiN coating,as well as TiA1SiN nanocomposite coating,were successfully employed for dry milling o
An M-coated Mg-8 mass％ Li alloy rectangular bar was fabricated by hot extrusion,and then,it was hot-rolled into a thin sheet.The Al coating was uniform in thickness and had good bonding with the substrate during all the processing.This Alcoated Mg-Li allo
A new kind of Mg-2Zn-0.6Ca (wt％) alloy was fabricated by casting and hot extrusion as a high-ductility structural material.The extruded alloy exhibits a superior elongation of ～ 30％,yield strength of 130 MPa and ultimate tensile strength of 280 MPa along
In the electromagnetic induction-controlled automated steel teeming (EICAST) technology of ladle,the height and location of the blocking layer are critical factors to determine the structure size and installation location of induction coil.And,they are al
The corrosion behavior of CoCrFeNiMox alloys was investigated in aqueous environments,NaCl and H2SO4 solutions,respectively,to simulate typical neutral and acidic conditions.The cyclic polarization curves in NaC1 and the potentiodynamic curves in H2SO4 cl
In addition to the advantage of the lightweight of magnesium alloys,magnesium composites have moderate strength and elastic modulus.The proposed application of magnesium composites as diesel truck pistons makes it necessary to assess their wear performanc
Single-pass compression tests were performed to investigate the hot deformation behavior of low-carbon boron microalloyed steel containing three various vanadium contents at 900-1100 ℃ and strain rate of 0.01-10 s-1 using the MMS-300 thermal mechanical si
Hot deformation behavior of 0.3C-15Cr-1Mo-0.5N high nitrogen martensitic stainless steel (HNMSS) was investigated in the temperature range of 1173-1473 K and at strain rates of 0.001-10 s-1 using a Gleeble 3500 thermal-mechanical simulator.The true stress
In this paper,we report the fabrication of the photocatalysts composed of Cu2O nanobelts and nanoporous Cu (NP Cu) substrate,which is obtained by soaking the NP Cu in dehydrated ethanol.The NP Cu substrate is achieved by dealloying of Ti40.6Zr9.4Cu40.6Ni6