Second-order interference of true thermal light from a warm atomic ensemble in two independent unbal

来源 :Photonics Research | 被引量 : 0次 | 上传用户:dotnetgroup
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
We report the demonstration of a second-order interference experiment by use of thermal light emitted from a warm atomic ensemble in two spatially separated unbalanced Michelson interferometers (UMIs). This novel multipath correlation interference with thermal light has been theoretically proposed by Tamma [New J. Phys.18, 032002 (2016)NJOPFM1367-263010.1088/1367-2630/18/3/032002]. In our experiment, the bright thermal light used for second-order interference is superradiantly emitted via collective two-photon coherence in Doppler-broadened cascade-type Rb87 atoms. Owing to the long coherence time of the thermal light from the atomic ensemble, we observe its second-order interference in the two independent UMIs by means of time-resolved coincidence detection. The temporal waveforms of the interfering thermal light in the two spatially separated UMIs exhibit similarities with the temporal two-photon waveform of time–energy entangled photon pairs in Franson interferometry. Our results can contribute toward a better understanding of the relation between first- and second-order interferences that are at the heart of photonics-based quantum information science.
其他文献
为揭示超声红外热成像检测中缺陷区域的生热机理,考虑预紧力对缺陷生热的影响,采用裂纹试件开展了预紧力分别为100、150、200 N的检测试验,发现裂纹区域温度与预紧力正相关,裂纹两端的生热量明显高于裂纹中段,尖端热斑最明显,且不同预紧力下圆形热斑最明亮。基于单自由度有阻尼位移激励系统和热源温度场叠加法建立了超声激励下裂纹生热的简易数学模型,通过计算参考点P■和裂纹尖端点P■的温度变化,发现P■点温度变化与试验结果一致,随着预紧力增大,P■点的计算结果与试验温升曲线拟合误差减小,且温升速率变化逐渐趋于一致。
From a classical dynamic simulation, we find the kinetic energy of the electrons generated during laser plasma generation depends on the laser polarization and intensity. The electron kinetic energy reaches its maximum with a fixed laser intensity for cir
Nano-TiO
可见光和近红外(Vis-NIR)光谱仪是一种实用的工具,可用于替代土壤物理和化学分析以评估土壤性质。最佳波段组合算法是一种通过考虑波段之间的相互作用信息来提取光谱变量的有效方法,但是对于实验室Vis-NIR光谱数据,该方法易受“维数灾难”的影响。提出一种适当地降低光谱配置(减少光谱带的数量和粗化光谱分辨率),以提高计算效率且不会显著影响预测精度的方法。首先,构建了6个光谱配置,即光谱波段的数量从2001个减小到19个,光谱分辨率从3 nm增加至100 nm,并且光谱采样间隔等于光谱分辨率(均匀间隔采样)。
基于条纹投射和正弦相位调制技术,提出了一种用于测量物体表面三维形貌信息的光纤干涉系统。通过杨氏双孔结构实现了条纹投射,并以余弦电压信号驱动压电陶瓷实现正弦相位调制。为了消除机械振动、温度波动等外部干扰,采用相位控制系统对相位漂移进行检测,并生成实时相位补偿信号。补偿后相位误差可达6.8 mrad,从而获得高精度的干涉条纹相位稳定度。对待测件的表面轮廓连续测量两次,时间间隔为10 min,测量重复度达到0.05波长。实验结果证明:该系统能够实现较高精度的表面形貌测量。
In view of dispersion compensating in multiple wavebands at the same time, this paper proposes a novel multi-waveband dispersion compensating fiber (DCF) based on hybrid photonic crystal fiber (PCF). The proposed fiber can compensate multiple wavebands at
期刊
为了满足激光诱导等离子体(LPP)体制下极紫外(EUV)光源对CO2激光器提出的稳定性需求, 建立了简化的CO2激光传输系统模型, 根据光束稳定性需求对光束功率、指向和位置的监测与控制方法进行了理论和实验研究。根据高功率CO2激光传输系统特点, 在实验室内建立了上述光束监测和控制实验系统, 包括光束功率控制模块、光束指向控制模块和光束参数监测模块, 其中光束参数监测模块可实时测量光束功率、指向、尺寸及发散角等重要参数。仿真与实验结果表明: 光束功率控制模块对线偏振激光功率的控制接近1%~100%, 光束指