【摘 要】
：
PVC (polyvinyl chloride) was isolated from waste plastic before manufacturing RPF (refuse paper & plastic fuel), and the characteristics of manufactured RPF including properties, calorific value, pyrolysis, chlorine content and kinetics analysis were anal
【机 构】
：
School of Architectural, Civil, Environmental and Energy Engineering, Major in Environmental and Ene
【出 处】
：
武汉理工大学学报（材料科学版）（英文版）
论文部分内容阅读
PVC (polyvinyl chloride) was isolated from waste plastic before manufacturing RPF (refuse paper & plastic fuel), and the characteristics of manufactured RPF including properties, calorific value, pyrolysis, chlorine content and kinetics analysis were analyzed. Based on the result of TGA (Thermogravimetric analysis), the kinetics characteristics was analyzed by using Kissinger method and Ozawa method which are the most common methods for obtaining activation energy, and the experimental conditions of TGA were set as follows: in a nitrogen atmosphere, with gas lfow rate of 20 mL/min, heating rate of 5-50℃/min, and maximum temperature of 800℃. In conclusion, the activation energy showed a tendency to gradually increase by a rise of reaction rate. Although the activation energy with pyrolysis of RPF was irregularly scattered, it was shown that the activation energy was stabilized by co-pyrolysis of RPF and additives (rice bran and sawdust).
其他文献
The resistivity of Hg0.89Mn0.11Te has been measured by the superconducting quantum interference device magnetometer in the temperature range from 5 to 200 K under the applied magnetic ifeld of 1, 2, 4 and 6.5 Tesla, respectively, compared with that of no-
Zirconium oxide (ZrO2) and boron carbide (B4C) were added to ZrB2 raw powders to prepare ZrB2 porous ceramics by reactive spark plasma sintering (RSPS). The reactions between ZrO2 and B4C which produce ZrB2 and gas (such as CO and B2O3) result in pore for
A novel biomimetic protein-resistant modifier based on cellulose-based polymeric liquid crystals was described (PLCs). Two types of PLCs of propyl hydroxypropyl cellulose ester (PPC) and octyl hydroxypropyl cellulose ester (OPC) were prepared by esterific
CuO-doped (Ag0.75Li0.1Na0.1K0.05)NbO3 (ALNKN-xCuO,x = 0-2mol%) lead-free piezoelectric ceramics were prepared by the solid-state reaction method in air atmosphere. The effects of CuO addition on the phase structure, microstructure, and piezoelectric prope
In order to study the size effect on the AE rate ‘a’ value, three kinds of mix ratios were set up by different particle sizes and water cement ratios, 45 cement mortar specimens with ifve different heights were tested under axial compression. And the whol
A novel micro fused-casting for metal (MFCM) process for producing A356 aluminum alloy slurry was proposed. MFCM means that the reifned metal slurry is pressed out from the outlet of bottom of crucible to the horizontal movable plate. With the aid of 3D m
The gas-phase dehydration of glycerol was conducted over HPW/MCM-41 catalysts, which were prepared by impregnation of different amount of H3PW12O40 (HPW) on the MCM-41 support. The samples were characterized by XRD, N2 physisorption, FTIR, NH3-TPD, and py
Ethylene glycol, glycerol, sorbitol, formamide, and urea were used as plasticizers for the preparation of thermoplastic starch (TPS) from corn starch. The properties of TPS were tested by analysis method. The results showed that TPSs were more highly plas
Ferrum niobate was synthesized by solid-phase sintering method in a vacuum carbon tube furnace at 1 300℃ for 180 min. The phase transformation of ferrum niobate carbothermal reduction process was studied by XRD. The reduction reactions of ferrum niobate i