Recrystallization相关论文
采用差示扫描量热仪(DSC)、光学显微镜(OM)、扫描电子显微镜(SEM)、X射线衍射仪(XRD)和拉伸试验机研究了固溶温度和时间对挤压态Al......
研究了DD483合金在服役温度附近经喷砂处理和退火后的组织演变和表面再结晶行为.将DD483合金试样在0.4～0.7 MPa的压力范围内进行喷......
研究了挤压温度对挤压态Mg-2Zn-1Y-0.5Zr生物可降解镁合金动态再结晶、织构和拉伸性能的影响,基于显微组织和腐蚀形态阐述了挤压态......
为解决Inconel 617合金的高温加工问题,对锻造Inconel 617合金的高温热变形行为进行了研究.利用Gleeble-3500热模拟试验机研究了In......
In this study, a tremolite marble from the Dabie ultrahigh-pressure (UHP) terrane, east-central China was investigated f......
...
Rapidly modifying microstructure and mechanical properties of AA7150 Al alloy processed with electro
Studies show that the proper solid solution treatment (SST) is a key step in the precipitation strength-ening of AA7150 ......
Evolution mechanism of recrystallization in a nickel-based single crystal superalloy under various c
The recrystallization behaviors of a nickel-based single crystal superalloy during heat treatment at 1,200 ℃ for 4 h wi......
Hot Deformation and Subsequent Annealing on the Microstructure and Hardness of an Al0.3CoCrFeNi High
The influence of simple thermomechanical processing such as hot deformation and heat treatment on the microstructure and......
采用传统搅拌摩擦焊(空冷)和快速冷却搅拌摩擦焊(液态二氧化碳)成功焊接2 mm厚的α-黄铜薄板.利用电子背散射衍射和透射电子显微术......
Effects of SiCp on microstructures of semi-solid extruded AZ91D magnesium alloys in recrystallizatio
AZ91D and 8.5vol.％ SiCp/AZ91D magnesium matrix composites were fabricated by a semi-solid extruded processing method, and......
Joint effect of quasicrystalline icosahedral and L12-strucutred phases precipitation on the grain st
Dispersoid hardening is a key factor in increasing the recrystallization resistance and mechanical strength of non-heat ......
本研究描述了一种从新鲜芒果叶片中分离纯化天然芒果苷的新颖简单且可大量制备的方法.以甲醇作为溶剂,采用超声辅助的方法从芒果叶......
In this paper,a comparative study on the spray deposited and as-cast 2195 alloy was carried out to reveal their microstr......
...
Texture Evolution and Dynamic Recrystallization of Zr-1Sn-0.3Nb-0.3Fe-0.1Cr Alloy During Hot Rolling
In the present work,the sheets of Zr-1Sn-0.3Nb-0.3Fe--0.1Cr alloy were hot rolled with different reductions (10％,30％,50％,an......
In this paper,electron backscatter diffraction and various other characterization and analysis techniques including X-ra......
Hot compression tests on AZ40 magnesium alloy were conducted on a Gleeble 1500d hot simulation testing machine in a defo......
...
...
Texture Evolution of 440 MPa Grade Nb-bearing High Strength IF Steel during Rolling and Annealing Pr
...
Recovery behavior studies of cold rolled steel sheet using X-ray line broadening during rapid heatin
Using X-ray diffraction techniques,the recovery behavior characteristics occurred in rapid heating treatment of cold rol......
Laser ultrasonics for metallurgy ( LUMet) is an innovative sensor technology for in-situ measurement of microstructure e......
Effects of rolling technology on electrochemical properties of Pb-0.06%Ca-l.2%Sn alloy anodes for co
In order to search for a good corrosion resistance, highly electrocatalytic activity and the long service life anode mat......
研究了不同退火工艺对Fe-0.3％Si电工钢微观组织的影响,并用EBSD检测了试验钢的微观取向.结果表明,开始再结晶时间从700℃的10s提前......
Dissimilar joining of oxide dispersion strengthened(ODS)steel and reduced activation ferritic/martensitic(RAFM)steel wou......
The recrystallization behaviors of pure tungsten with different rolling reductions were investigated by isothermal annea......
Preparation and Properties of High Purity α-Al2O3 Particles Derived from waste Anodic Aluminum Oxida
Anodising industries produces large quantity of waste acid solutions containing high amounts of SO42-and Al ions.The wor......
The significant distribution of {411 } texture exists during the preparation of thin-gauge grain-oriented silicon steel......
Repeated deformation with optimum reductions in roughing mill exceeds the critical amount of strain required for recryst......
Properties of a co-processed compound versus the physical blend based on lactose and microcrystallin
Purpose A new co-processed compound made of lactose and microcrystalline cellulose (MCC) was prepared for direct compres......
Integrated Modelling of Microstructural Evolutions in Friction Stir Welding/Friction Stir Additive M
Friction stir welding(FSW)has been invented for more than twenty years.Based on friction stir welding,new technologies a......
...
Coupled fast Fourier transform-based crystal plasticity model and cellular automaton approach for mo
An effective computational approach for modeling recrystallization of plastically deformed polycrystals in three dimensi......
通过改变试样在热处理过程中的升温速率，研究了升温速率对激光立体成形（LSF）GH4169合金再结晶过程的影响，分析了升温速率对再结晶形核......
研究Mg-10Gd-1.5Y-0.4Zr合金的磨损率变化、磨损转变及其与载荷和温度之间的关系.在20～200℃试验温度范围内,在销盘式试验机上进行......
研究了不同应变速率、温度和应变下变形的Al-Mg-Si合金本构关系。定量表征和分析了热变形和热处理过程中合金的等微观组织演变,包......
Morphology control of perovskite films is of critical importance for high-performance photovoltaic devices. Although sol......
对具有片层组织的TC21钛合金金进行热轧和退火试验(退火温度:820、880、940℃;退火时间:1、6 h),进而研究退火参数对α和β相静态......
研究通过铸造法制备的含Al3(Sc,Zr)相的7075铝合金静态再结晶行为和再结晶行为与力学性能的关系。Sc和Zr复合添加使Sc−Zr−7075铝......
N,N-Dimethylamino-2,6-diisopropylanilidoMetal Zr Compound and the Catalytic Behaviors in Ethylene Po
Organoamidolithium compounds have been extensively studied for their reactivities and transformation of organoamido-......
The continuous dynamic recrystallization(CDRX) through a progressive transformation of a subgrain structure into a grain......
Modelling of dynamic recrystallization kinetics of 300M steel at high strain rates during hot deform
The flow curves of 300M steel exhibit a transition from stress peak presence to stress peak absence as the strain rate i......
Turbine discs in gas-turbine engines always experience high-temperature and high-stress environment.Extensive investigat......
Morphology control of perovskite films is of critical importance for high-performance photovoltaic devices.Although solv......
Although Cu was studied extensively,the Hall-Petch relationship was mainly reported in the coarse-grained regime.In this......
