Solar radiation pressure used for formation flying control around the Sun-Earth libration point

来源 :应用数学和力学(英文版) | 被引量 : 0次 | 上传用户:liwl11
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
Solar radiation pressure is used to control the formation flying around the L2 libration point in the Sun-Earth system. Formation flying control around a halo orbit requires a very small thrust that cannot be satisfied by the latest thrusters. The key contribution of this paper is that the continuous low thrust is produced by solar radiation pressure to achieve the tight formation flying around the libration point. However, only certain families of formation types can be controlled by solar radiation pressure since the direction of solar radiation pressure is restricted to a certain range. Two types of feasible formations using solar radiation pressure control are designed. The conditions of feasible formations are given analytically. Simulations are presented for each case, and the results show that the formations are well controlled by solar radiation pressure.
其他文献
将弯、掠叶片的三维设计技术应用于离心风机叶轮,根据积叠线在周向和子午面内的变化,分别研究正弯、反弯、前掠、后掠、前倾、后倾、前掠正弯和后倾正弯8种叶片。通过比对不
针对动态特性稳健性设计,摒弃传统的信噪比分析方法,直接由响应变量与信号因子之间的线性关系,利用灰色关联度衡量响应变量与信号因子之间的关联程度,选取一组使得关联度最大
or shock waves.Combined with the adaptive remeshing technique,satisfactory results can be obtained.
A meshless simulation system is presented for elastic deformation driven by skeleton in this paper. In this system, we propose a new method for calculating node
为了能在外场对红外跟踪测量系统的脱靶量误差进行快速的检测修正,分析了脱靶量误差的主要来源,并建立了脱靶量误差的数学模型;根据这一模型,提出了一种基于场景的脱靶量误差
分束棱镜是大型空间遥感器分离光束的重要部件。为解决空间遥感器中大型分束棱镜的支撑问题,对尺寸为200mm×200mm×200mm的分束棱镜的支撑结构展开研究。提出基于半运动学支撑和被动温度补偿原理的立方分束棱镜支撑结构,建立棱镜的接触约束,模拟边界条件的非线性,利用非线性有限元方法进行工程分析,最后分析验证。结果显示,在自重与±15℃稳态温度变化耦合作用下分束棱镜通光面面形误差PV值优于73.2n
为研究环形燃烧室出口温度分布特性,以某型燃气轮机双级旋流回流环形燃烧室作为研究对象,分别采用数值分析和试验的方法,研究该燃烧室流场特性和出口温度分布特性。数值模拟
通过电学温敏参数法测得多发光区大功率激光器瞬态加热响应曲线,利用结构函数法给出了多发光区激光器热阻构成,分析了多发光区激光器热特性.通过串并联热阻网络模型刻画了单
结合规则推理和实例推理推理模型,提出针对锅炉设计的模糊评估算法,经过模型与算法的结合,可有效实现锅炉的智能化设计。通过对设计过程的详细描述,给出了锅炉参数化设计中相
干涉仪系统传递函数能有效地表征系统相位成像的性能.通过假设干涉成像系统是复振幅的线性平移不变系统,模拟计算正弦相位光栅和相位台阶这两类标准相位物体的成像,确定干涉