论文部分内容阅读
治则与治法理论在中医理论体系中居于重要位置，在中医理论研究中属相对薄弱环节，应该重视经典名著有关治则、治法理论的挖掘，重视名老中医学术传承，同时注意结合现代临床实际，参考现代医学相关认识，深入领会中医治则与治法理论，并不断创新，促进中医学术进步。
传承创新治则治法理论,提高现代中医临床疗效
【摘 要】
：
治则与治法理论在中医理论体系中居于重要位置，在中医理论研究中属相对薄弱环节，应该重视经典名著有关治则、治法理论的挖掘，重视名老中医学术传承，同时注意结合现代临床实际，参考
【机 构】
：
首都医科大学附属北京中医医院呼吸科,中国中医科学院病因病机研究室,北京中医药大学东直门医院内分泌科,北京中医药大学研究生院,北京中医药大学东直门医院心内科,中国中医科学院中医临床基础医学研究所,首都医
【出 处】
：
环球中医药
【发表日期】
：
2004年期
【基金项目】
：
国家“十二五”科技支撑计划;
其他文献
The hot deformation behaviors of solution treated Mg-1.8Mn-0.4Er-0.2Al alloys were investigated by means of compression tests on Gleeble-1500 in strain rate ran
Void damage evolution of LF6 aluminum alloy welded joints under external load and thermal cycling co
Based on the simulated aerospace thermal cycling tests, the effect of thermal cycle on the void damage evolution mechanism of LF6 aluminum alloy welded joint wa
众所周知文化产业是当今社会发展最快的产业之一，特别是国家的重点扶植和社会的高度关注，都标志着中国文化大发展的新时代开始了。与此同时另一个朝阳产业，也在东北这片黑土地上
Phase evolution and room temperature ferroelectric and magnetic properties of Fe-doped BaTiO3 cerami
To make the ferroelectric BaTiO3 possess ferromagnetism simultaneously, magnetic Fe was doped into BaTiO3 ceramics at doping levels up to 10% (molar fraction).
Purification and enzymatic properties of arsenic resistance protein ArsH from heterogeneous expressi
Four arsenic-resistance genes (arsB, arsC, arsH, arsR) have been discovered in Acidithiobacillus ferrooxidans. Their gene sequences have been identified and thr
Electron beam welding of Ti-15-3 titanium alloy to 304 stainless steel with a copper sheet as interlayer was carried out. Microstructures of the joint were stud
编组站配流问题是研究车站作业计划优化编制的主线，是站调阶段计划的核心．为了实现配流的协同优化，综合考虑解体调机、编组调机、到发线运用、取送车作业、配流等约束，对总车流量
Optical microscope, X-ray diffractometer, scanning electron microscope, tensile tester and dynamic mechanical analyzer (DMA) were applied to investigate the eff
Microstructural zones and tensile characteristics of friction stir welded joint of TC4 titanium allo
TC4 titanium alloy was friction stir welded using a W-Re pin tool, and the defect-free weld was produced with proper welding parameters. The joint consists of s