【摘 要】
：
TiC particle and TiBwhisker reinforced Ti-6Al-4V composites was in situ synthesized by a method of Vacuum Arc Remelting.The infuence of the indirect extrusion process on the microstructure and mechani
【机 构】
：
State Key Laboratory of Metal Matrix Composites,School of Materials Science and Engineering,Shanghai
论文部分内容阅读
TiC particle and TiBwhisker reinforced Ti-6Al-4V composites was in situ synthesized by a method of Vacuum Arc Remelting.The infuence of the indirect extrusion process on the microstructure and mechanical properties of(TiB+TiC)/Ti-6Al-4V Composite was studied by experiments.The results show that the indirect extrusion process makes the TiC particle and TiB whisker more homogenous in distribution and more uniform in size.The reinforcements are orientated along extrusion direction orderly and the ratio of TiB whisker is reduced sharply after the indirect extrusion.Meanwhile,the matrix microstructure is refned too.Thus,the strength and plasticity of the composite are improved obviously.
其他文献
One of the most significant problems of chemotherapy is that even originally very sensitive tumors become often resistant to cytostatic after several cycles of treatment.This so-called multidrug resis
Drug delivery systems (DDS) have appeared as a promising and reliable approach to delivering potent drugs to the site of action precisely and timely,in which polymeric nanosystems including micelles,n
In recent years,chitosan microspheres have attracted more and more attention as a carrier for drug delivery because chitosan has good compatibility,biodegradability,and biological adhesion properties.
Chitosan has been adopted to have great potential in pharmaceutical science due to its outstanding properties including nontoxicity,biocompatibility,biodegradability,mucus-adhesion,and low cost.To pre
Deep brain stimulation (DBS) is a well-developed neurosurgical technique for the treatment of numerous neurological disorders.It is important to understand the cerebral processes triggered by DBS [1].
氙气具有较低的电离能和较高的原子质量,是电推力器通常使用的推进剂.在地面进行电推力器真空试验时,需要采用真空抽气系统抽除真空容器内氙气,国内外早期电推力器大型真空试验设备,通常采用油扩散泵作为氙气主要抽气泵,近年来,随着制冷机的日臻完善,更洁净的制冷机低温泵得到迅速发展,在此类设备上逐渐代替了油扩散泵.兰州华宇航天技术应用有限责任公司根据兰州空间技术物理研究所的长寿面、高可靠性电推力器试验设备需求
非真空累积采样过程中，由于采样系统和氦质谱检漏仪是在测试间的大气环境中，同时采样系统存在负压，+氦质谱检漏仪为真空系统，采样系统管路以及检漏仪本身存在的密封问题会造成测试结果受大气环境影响。由于大气环境中的氦气浓度存在不确定性，进入采样系统或者检漏仪中会造成读数被大气环境拉偏。本文通过实验研究，分析出各个密封环节的影响大小，以及测试读数的变化规律曲线，最终提出明显影响的辨识方法和避免措施。
复合分子泵结合了涡轮分子泵大抽速、牵引分子泵压缩比高的优点，在很宽压力范围内具有优越的性能，已经成为半导体薄膜制备等领域中的重要真空获得设备。随着复合分子泵应用领域的扩宽，其牵引级的工作条件已经由分子流态扩展到过渡流，甚至到了粘滞流态下。牵引分子泵分子流、粘滞流态下的抽气特性计算已有较成熟的方法，其过渡流态下的计算成为复合分子泵设计计算的核心问题。本文以分子流和粘滞流态下牵引泵抽气性能计算式为基本
以含砷锑复杂铜镍合金为原料,从理论上分析了采用真空蒸馏法综合回收该类物料中有价金属Cu,Ni 和Ag 的可行性,并通过实验探讨了蒸馏温度、保温时间、元素As,Sb 对Cu,Ni,Ag 分离和富集效果的影响.实验结果表明：在蒸馏温度1473K,保温时间120min,系统残压10～30Pa 条件下,残余物中Cu 含量升至8.83％,直收率为88％左右；残余物中Ni 含量升至25.61％,直收率为91％
筒式牵引分子泵具有结构简单、压缩比高等优点，常常作为复合分子泵中的压缩级，在清洁高真空、超高真空环境的获得中起到了重要作用。筒式牵引分子泵抽气性能受螺旋几何参数、螺旋槽数量以及转子转数等影响，其中螺旋升角对泵抽速和压缩比均有重要影响。本文考虑了牵引转子与定子间隙返流对抽气性能的影响，获得了压差产生轴向返流和转子牵引引起周向泄漏条件下抽速和压缩比的计算式。计算结果表明，泵抽速、压缩比随螺旋升角的增加