一种适用于三维混合网格的GMRES加速收敛新方法

来源 :航空学报 | 被引量 : 0次 | 上传用户:qx552801
下载到本地 , 更方便阅读
声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架
论文部分内容阅读
为提高流场计算收敛效率,发展了一套适用于三维混合网格Naiver-Stokes方程求解的并行广义最小残差(GMRES)隐式时间推进方法。该方法由科学计算可移植扩展工具包(PETSc)中的Krylov子空间求解器实现,线性方程系统中的系数矩阵直接以显式给出以提高算法的稳定性。为进一步提高GMRES方法的收敛速度,对非结构网格的序号进行了重排序,使得系数矩阵的非零元素尽量向主对角线靠近。利用所发展的GMRES方法,完成了对ONERAM6机翼、AIAA阻力预测会议通用研究模型(CRM)等算例的计算,计算结果与试验结果吻合良好。通过与其他隐式推进方法进行比较,对算法的收敛特性进行了研究。结果表明,所发展的GMRES方法计算更加稳定,残差下降速度相对LU-SGS(Lower-Upper Symmetric Gauss-Seidel)方法更快,尤其是气动力系数向着收敛解逼近的速度更加明显,提高了计算效率。 In order to improve the convergence efficiency of the flow field, a parallel generalized minimum residual (GMRES) implicit time-based method for solving the Nai-Stokes equations of three-dimensional hybrid grid is developed. The method is implemented by Krylov subspace solver in PETSc, and the coefficient matrix in linear equation system is given directly to improve the stability of the algorithm. In order to further improve the convergence rate of GMRES method, the sequence numbers of unstructured grids are reordered so that the non-zero elements of the coefficient matrix approach the main diagonal as far as possible. By using the developed GMRES method, the calculation of the ONERAM6 wing and the AIAA General Resistance Prediction Conference Model (CRM) was completed. The calculated results are in good agreement with the experimental results. By comparing with other implicit methods, the convergence of the algorithm is studied. The results show that the developed GMRES method is more stable and the rate of residual descent is faster than the Lower-Upper Symmetric Gauss-Seidel (LU-SGS) method, especially the aerodynamic coefficient approaches the convergent solution more quickly, effectiveness.
其他文献
Background:Systemic administration ofbisphosphonates has shown promising results in the treatment ofosteonecrosis of the femoral head (ONFH).However,few studies
Background:There is conflicting evidence as to whether the femoral head should be preserved or replaced in elderly patients with displaced intracapsular femoral
西门子数控系统在国内的应用比较多,欲使其发挥正常效能,延长使用寿命,须进行正确的维护和修理。为此,本刊特邀西门子(中国)有限公司自动化及驱动产品部张泰华撰写了“西门子数控
二、关于诊断软件技术的发展趋势rn  关于诊断软件从1996年到现在,其主要技术如表5所示。表5中没包括检测和对策技术,这是因为:检测技术大体上是由过去的技术发展来的。对其余
采用数值方法研究了加装非线性能量汇(NES)的二维机翼在不同速度来流下的振动响应机制,着重探索了NES对系统振动的抑制以及系统内的靶向能量传递(TET)特性。首先,建立了加装
8 机床负荷试验8.1 主传动系统最大扭矩和最大切削抗力试验8.1.1 试验方法 用强力车削外圆(无冷却液)进行切削,并按表5格式记录(略)。 切削时可逐渐改变进给量或切削深度以
60.推力轴承安装时,其轴圈、座圈位置不能互换。 61.表征振动的物理量有振幅、频率和振动周期。 62.机构中的机架,由于装在它上面的部件发生振动而引起的振动叫做共振。 63.
抗精子抗体所致免疫性不孕是不孕不育科常见病之一.近年来,笔者应用自制的抗免促孕胶囊治疗116例,疗效满意,现总结如下.
60.[○] 推力轴承的轴圈、座圈、外形虽相似,但实际尺寸与作用不同。轴圈内径有公差要求,与轴紧密配合且一起转动;座圈外径与轴承座紧密配合,孔径比轴圈内孔稍大,工作时座圈静止不