【摘 要】
：
A novel fusion bonding method between silicon and glass with Nd:YAG laser is described. This method overcomes the movable mechanical parts damage caused by the electrostatics force in micro-electronic machine-system (MEMS) device during the anodic bonding
【机 构】
：
CollegeofElectronicInformation
【出 处】
：
ChineseOpticsLetters
论文部分内容阅读
A novel fusion bonding method between silicon and glass with Nd:YAG laser is described. This method overcomes the movable mechanical parts damage caused by the electrostatics force in micro-electronic machine-system (MEMS) device during the anodic bonding. The diameter of laser spot is 300 μm, the power of laser is 100 W, the laser velocity for bonding is 0.05 m/s, the average bonding tension is 6.3 MPa. It could distinctly reduce and eliminate the defects and damage, especially in movable sensitive mechanical parts of MEMS device.
其他文献
用远红外环形谐振腔代替线形谐振腔可以大大减小光泵连续波远红外激光器的振幅噪声。在远红外激光器达到精确稳频的远红外谱线中心，激光发射从顺时针模变为逆时针模。对于某一模式采用辅助后向反射时，单向输出出现于整个激光调谐宽度之内。
A model of steady-state rate equations including amplified spontaneous emission for long-wavelength ytterbi-um-doped fiber laser is set up, which provides design principle for a practical laser system. We demonstrate a diode-pumped all-fiber Yb-doped fibe
Radiation-induced attenuation (RIA) in four types of polarization-maintaining optical fibers for interferometric fiberoptic gyroscope (IFOG) at 1310 nm is measured. The measurements are conducted during and after steady-state γ-ray irradiation using a 60C
In this paper, a 20 nm palladium-silver (Pd/Ag) ultrathin optical film is used for hydrogen gas sensing. The mole ratio of the two metals is controlled at Pd:Ag=3:1. In the direct current (DC) sputtering machine, the optical thin film is evaporated on the
步态识别在反恐、安防、智能监控和现实挖掘等领域具有广泛的应用前景,但现有的二维步态分析方法在面对视角变化、物体携带等复杂应用场景时受到限制。对此,探讨一种以人体点云数据为基础的三维参数化步态建模和识别方法。运用深度摄像机获取人体点云数据,对标准的参数化人体模型进行形体和姿态变形;通过观测步态点云轮廓与标准三维参数人体轮廓之间的距离度量函数,运用改进鲍威尔法进行极小值求解,实现人体点云数据到三维参数
针对当前图像显著性检测算法存在的检测不准确和边缘不清晰问题,提出基于改进的贝叶斯公式融合算法。采用compactness先验得到初级显著图,并以初级显著图作为训练样本,采用多核学习方式得到次级显著图,而后基于贝叶斯公式以一定的比例融合初级和次级显著图,最终获得精确的显著性检测图。实验结果表明,算法在2个公开数据集上进行检测时,所得结果能够有效地突出目标物体,去除边缘模糊的现象,且实验结果在3个数据
激光熔覆零件疲劳寿命评估一直是制约激光熔覆技术在工程中推广应用的一个重要因素, 现有研究多为试验研究, 缺乏理论分析。为量化评估激光熔覆试件的疲劳寿命, 并确定熔覆过程的最优速度参数, 采用能量法, 综合考虑相变及熔覆过程能量变化规律, 建立了激光熔覆构件疲劳寿命评估模型, 模型计算结果和试验结果基本吻合。评估模型计算结果表明采用同步送粉法, 激光功率、光斑直径及送粉速率一定的情况下, V是180mm/min时为最优参数。
Nitridated \beta-Ga2O3 (100) substrate was investigated as the substrate for GaN epitaxial growth. The effects of nitridation temperature and surface roughness of \beta-Ga2O3 wafers on the formation of GaN were studied. It was found that the most optimi