【摘 要】
：
The effect of lead on the initial corrosion behavior of 316LN stainless steel has been investigated by U-bend immersion experiments in 4 wt％ NaOH solutions at 300 ℃.Follow-up studies after soaking were carried out by scanning electron microscope,energy di
【机 构】
：
Corrosion and Protection Center, University of Science and Technology Beijing, Beijing 100083, China
论文部分内容阅读
The effect of lead on the initial corrosion behavior of 316LN stainless steel has been investigated by U-bend immersion experiments in 4 wt％ NaOH solutions at 300 ℃.Follow-up studies after soaking were carried out by scanning electron microscope,energy dispersive X-ray spectrometer,X-ray photoelectron spectrometer,Auger electron spectroscopy and Raman spectroscopy.The results show that lead affects the properties of the oxide film by changing the thickness and composition,which leads to an increase in the sensitivity of stress corrosion cracking of 316LN stainless steel.Pits and cracks appeared on the surface of 316LN stainless steel under both lead-free and lead-containing conditions.The corrosion products were oxides of Fe,Cr and Ni,and the main spinel structure on the surface of the film was NiCr2O4 under both conditions.However,in the presence of lead,the cracks and pits were more obvious,the thickness of the film increased from 50 to 200 nm,and the amount of protective NiCr2O4 decreased.Lead was concluded to be involved in the dehydration reactions in the form of Pb(OH)2,which affected the normal dehydration process of the hydroxides and inhibited the formation of spinel structures.Because of the above characteristics of lead,the stability of the oxide film and its protection of 316LN stainless steel were reduced.
其他文献
Three-dimensional distribution of solute elements in an Mg-Zn--Gd alloy during ageing process is quantitatively characterized by three-dimensional atom probe (3DAP) tomography.Based on the radius distribution function,it is found that Zn-Gd solute pairs i
To explore the optimum use of stabilised elements and study the influences of stabilisation in 18Cr-2Mo grades,the Nb and Nb + Ti microalloying investigation focused on the relationships of the microstructure and mechanical properties of the microalloyed
Rutile (TiO2) particle-reinforced aluminum matrix composites were prepared by friction stir processing.The microstructure was studied using conventional and advanced characterization techniques.TiO2 particles were found to be dispersed uniformly in the co
In this research,2205/Q235B clad plates were prepared by a vacuum hot rolling composite process.The effects of adding Fe,Ni,and Nb interlayers on the bonding interface structures and the shear strengths of the clad steel plates were studied.The results sh
Coarsening of cuboidal γ\'precipitates and relevant diffusion process in Ni-based single-crystal superalloy CMSX-4 were investigated at 1000,1020 and 1040 ℃ for specific times.The γ\'coarsening kinetics followed a cubic rate law with time and was pres
The microstructure and mechanical properties of NiCrMoV-and NiCrSi-alloyed medium-carbon steels were investigated after multiple tempering.After austenitising,the steels were hardened by oil quenching and subsequently double or triple tempered at temperat
To understand the atomistic mechanisms of tension failure of Ni-based superalloy,in this study,the classical molecular dynamics (MD) simulations were used to study the uniaxial tension processes of both the Ni/Ni3Al interface systems and the pure Ni and N
In the present work,the electrochemical behavior and properties of the passive film of a new Sn-alloyed 316LX austenitic stainless steel were investigated.With the increase in Sn content in 316LX austenitic stainless steel from 0 to 0.21％,the critical pit
Mg-2Al-1.2Ca-0.2Mn (at％)-based alloys with Ce-rich mischmetal (MM) substitution of 0-0.6 at％ for Ca were hot extruded at 400 ℃.The effect of MM substitution on the microstructure and mechanical properties of the extruded alloys was investigated.The as-cas
The high-current pulsed electron beam (HCPEB) treatment with current density 6 J/cm2 was applied on AZ91 Mg alloy to improve its corrosion resistance.Results showed that the net-like Mg17Al12 disappeared on the surface of AZ91 Mg alloy after irradiation b