2. 您的位置
3. 首页
4. 期刊论文
5. Enhanced strength and electrical conductivity of Al-0.3Ce alloy simultaneously with Ti(C,N)nanoparti

Enhanced strength and electrical conductivity of Al-0.3Ce alloy simultaneously with Ti(C,N)nanoparti

来源 :稀有金属:英文版 | 被引量 : 0次 | 上传用户：haidiaiqing

【摘 要】

：

Ti(C,N)nanoparticles were added to an Al-0.3 Ce alloy by ultrasonic treatment.Further annealing at 570℃for4 h afforded the ultimate tensile strength of 79 MPa and electrical conductivity of 64.0%IACS for the Al-0.3 Ce alloy with1.5 vol%Ti(C,N)addition.Bot

【作 者】

：

Wan-Peng Li Yu-Liang Zhang Jian Mao 

【机 构】

：

CollegeofMaterialsScienceandEngineering

【出 处】

：

稀有金属:英文版

【发表日期】

：

2021年7期

【关键词】

：

Conductive aluminum alloy Ti(C N)nanoparticles Ce Micro-nano hierarchical spheri 

【基金项目】

：

Panxi Strategic Resources Innovation Development Fund of Sichuan Province(No.1840STC30704/01)。

下载到本地 , 更方便阅读

下载此文 赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

Ti(C,N)nanoparticles were added to an Al-0.3 Ce alloy by ultrasonic treatment.Further annealing at 570℃for4 h afforded the ultimate tensile strength of 79 MPa and electrical conductivity of 64.0%IACS for the Al-0.3 Ce alloy with1.5 vol%Ti(C,N)addition.Bot

其他文献

A new insight into rapid oxidation of alloy 925 contaminated by oxide powder

Rapid oxidation takes place both in the laboratory and in industrial conditions when alloy 925 is contaminated by oxide powder,and the oxidation rate is much higher than normal.Herein,the rapid oxidation behavior and mechanism of alloy 925 were investigat

期刊

RapidoxidationSynergeticeffectNickelbasedsuperalloy

Microstructure and mechanical properties of TC4 joints brazed with Ti-Zr-Cu-Sn amorphous filler allo

The Ti_51.44Zr_16.26Cu₃₀Sn_2.3(at%)amorphous filler alloy in a ribbon form was prepared by melt spinning.The Ti-6 Al-4 V alloy was brazed in vacuum furnace by using the Ti_51.44Zr_16.26Cu₃₀

期刊

AmorphousalloyBRAZINGTitaniumalloyMicrostructureMechanicalproperty

Microstructure and properties of Al2O3-ZrO2-TiO2 composite coatings prepared by plasma spraying

Al2O3-ZrO2-TiO2 coatings were successfully prepared by plasma spraying Al2O3-ZrO2 composite powders with and without TiO2 addition.The effects of TiO2 on the ph

期刊

Al2O3-ZrO2Composite coatingsPlasma sprayingTiO2

Microstructure and mechanical properties of TiAl/Ni-based superalloy joints vacuum brazed with Ti-Zr

For the purpose of elevated temperature service and weight reduction in aerospace vehicle applications,a novel Ti-Zr-Fe-Cu-Ni-Co-Mo filler metal was employed to join TiAl to Ni-based superalloy(GH536).The effects of brazing temperature on interfacial micr

期刊

TiAlalloyNi-basedsuperalloyBRAZINGMicrostructureShearstrength

Microstructure,mechanical properties and stretch formability of as-rolled Mg alloys with Zn and Er a

The magnesium alloy has a unique advantage in 3C fields due to its high specific strength and excellent electromagnetic shielding characteristic.However,it is d

期刊

Mg-Zn-Er alloyHot rollingTextureShear bandStretch formability

Oxidation behavior of multi-component Ta-W-Al-Ti alloy at 1173 K

Ta-W alloys have unique properties but their applications at high temperatures are restricted due to their poor oxidation resistances.The addition of Al and Ti

期刊

Oxidation behaviorTa-W-based alloyAluminumTitanium

Microstructure and mechanical properties of spark plasma-sintered La2O3 dispersion-strengthened W-Ni

An investigation of lanthanum oxide (La2O3)addition to tungsten heavy alloy (WHA) with a ternary composition of W-7Ni-3Fe was reported in this study.The mixed p

期刊

Tungsten heavy alloysLanthanum oxideSpark plasma sinteringMicrostructureMech

中高频椭圆铰链双光纤光栅加速度传感器

针对现有光学传感器难以满足大型结构中高频振动监测的需求,提出一种基于椭圆铰链的中高频双光纤布拉格光栅加速度传感器。基于传感器理论模型分析传感器的灵敏度和谐振频率,采用MATLAB和ANSYS软件对传感器的结构参数进行优化及仿真,研制双光纤布拉格光栅传感器,并进行传感器灵敏度标定实验。结果表明:传感器的谐振频率约为780 Hz,灵敏度为132.53 pm/g,横向抗干扰度小于3.3%,可用于80~500 Hz之间振动信号的实时监测。

期刊

光纤传感器光纤布拉格光栅(FBG)椭圆铰链中高频

Hot pressing sintering process and sintering mechanism of W-La2O3-Y2O3-ZrO2

The W-La₂O₃-Y₂O₃-ZrO₂materials were prepared by vacuum hot pressing sintering process.The microstructure was characterized by scanning electron microscopy(SEM).The effects of sintering temperature,sin

期刊

W-La_(2)O_(3)-Y_(2)O_(3)-ZrO_(2)HotpressingsinteringRelativedensityTungste

Deposition and characterization for high-quality Ti-Ni-Cu thin films with higher Cu content

In order to attain high-quality Ti-Ni-Cu film,the surface morphologies,chemical compositions and mechanical properties of Ti-Ni-Cu thin films prepared by direct current(DC)magnetron sputtering at various processes were characterized by scanning electron m

期刊

Ti-Ni-CuthinfilmDCmagnetronsputteringSputteringparametersChemicalcompos