nanohardness相关论文
γ-Alumina Thin Films Deposited by Magnetron Sputtering with Resputtering Technique at Low Temperatur
...
The influence of substrate-target orientation on the properties of ZrN films deposited by arc ion pl
The crystallograpic structure and properties of Zirconium nitride (ZrN) films deposited on 304 stainless steel were inve......
Influence of heat treatment on microstructure and nanohardness of TiAl alloy solidified under high p
The Ti-48at.％Al alloy solidified under different pressures was prepared using a tungsten-carbide six-anvil apparatus and ......
Conversion between Vickers hardness and nanohardness by correcting projected area with sink-in and p
The Vickers hardness test has been widely used for neutron-irradiated materials and nanoindentation for ion-irradiated m......
该文从挂篮荷载计算、施工流程、支座及临时固结施工、挂篮安装及试验、合拢段施工、模板制作安装、钢筋安装、混凝土的浇筑及养生......
目的 研究人牙釉质和牙本质的纳米硬度与显微组织的关系.方法 利用纳米力学探针、透射电镜及红外光谱仪等设备分别对牙釉质和牙本......
The aim of this work is to investigate microstructure,corrosion resistance characteristics and nanohardness of the oxide......
纳米压痕装置是一种具有纳米级压痕深度检测能力,能够完成载荷-位移测量的一种装置,根据所得到的载荷-位移曲线可以用来获得材料的......
...
采用原子力显微镜纳米压痕法测量了Gr/Al复合材料热循环后界面附近的纳米硬度和塑性变形能力的分布。随热循环次数的增加，纤维和基......
目的:人牙釉质内的力学性能分布,对实现釉质的优异性能起到了重要作用,因而本工作的目的是使用结合原子力显微镜(Atomic Force Mic......
以微机电系统常用的单晶硅材料和经氮离子注入单晶硅后形成的表面改性层为研究对象，在原位纳米力学测试系统上进行微压痕实验，对样品......
采用离子束溅射与磁过滤阴极弧共沉积技术在单晶硅片(400)表面制备Si含量(摩尔分数)为3.2%~15.5%范围内的TiSiN薄膜。采用X射线光......
使用纳米硬度计对单晶铝进行了纳米压痕试验,利用原子力显微镜对压痕形貌进行扫描并计算硬度值,重点观察和分析了纳米级条件下单晶......
对微机械而言,不仅微观环境对其工作性能有所影响,而且微构件本身的力学性能也直接影响到微机械的服役寿命和工作性能.在微小尺度......
利用直流磁控溅射方法制备了Fe／Cu纳米多层膜，使用扫描电子显微镜（SEM）、薄膜应力分布测试仪和纳米压痕技术研究了不同周期结构Fe／Cu纳......
通过扫描电镜(SEM)研究了稀土氧化物La2O3对铁基合金激光熔覆层组织形貌的影响,用纳米硬度探针测定了熔覆层与基体界面附近和搭接......
目的研究脉冲偏压占空比对TiN／TiAlN多层薄膜微观结构和硬度的影响规律。方法利用脉冲偏压电弧离子镀的方法，改变脉冲偏压占空比，在M2......
Changing of Defect’s Structure and Properties of Superhard Nanostructured Ti-Si-N Coatings, Fabricat
Using such unique methods of analysis as slow positron beam (SPB), RBS, μ-PIXE (proton microbeam), XRD, SEM with EDS, X......
Nanocomposites consisting of multiwall carbon nanotubes (MWCNT) and epoxy resin were produced by a standard calendaring ......
